AdvancedRouting, Add/Edit Route | SMC Networks SMCWBR14-N2 specification

Advanced_Routing

Add/Edit Route

Adds a new route to the IP routing table or edits an existing route.

Enable: Specifies whether the entry will be enabled or disabled.

Destination IP: The IP address of packets that will take this route.

Netmask: One bits in the mask specify which bits of the IP address must match.

Gateway: Specifies the next hop to be taken if this route is used. A gateway of 0.0.0.0 implies there is no next hop, and the IP address matched is directly connected to the router on the interface specified: LAN or WAN.

Interface: Specifies the interface -- LAN or WAN -- that the IP packet must use to transit out of the router, when this route is used.

Metric: The route metric is a value from 1 to 16 that indicates the cost of using this route. A value of 1 is the lowest cost, and 15 is the highest cost. A value of 16 indicates that the route is not reachable from this router. When trying to reach a particular destination, computers on your network will select the best route, ignoring unreachable routes.

34

Image 37

SMC Networks SMCWBR14-N2 manual AdvancedRouting, Add/Edit Route

Contents

User Guide Limited Warranty Page Important Note CE Mark Declaration of Conformance for EMI and Safety EECFCC Radiation Exposure Statement Iii Table of Contents SMCWBR14-N2 Package Contents AD-HOCIBSS Network Wireless LAN Networking Channel for each station Page Roaming in an ESS network diagram Introduction Hardware Overview Front Panel LED’s Getting Started ¾ Click Log Using the Configuration Menu BasicInternet Basic BasicWireless Wireless Network Name Enable WirelessEnable Auto Channel Scan Wireless Channel Example WEPWPA-Personal and WPA-Enterprise WPA-Personal Advanced Optional Backup Radius Server BasicNetwork Settings Enable RIP Router SettingsRIP Operating mode IP Address Allow RIP updates from WAN Act as default routerRIP Password Dhcp Server Settings Always Broadcast Dhcp Lease TimeAdd/Edit Dhcp Reservation Computer Name Number of Dynamic Dhcp Clients Dhcp Reservations ListRevoke Reserve AdvancedVirtual Server Advanced Protocol Virtual Server Parameters NamePrivate Port Public Port Schedule EnableAdd/Edit Virtual Server Save Parameters for an Application Rule Example AdvancedSpecial ApplicationsApplication Trigger Protocol Trigger Port RangeInput Port Range Input Protocol AdvancedGaming TCP Ports To Open Port Forwarding Fields NameUDP Ports To Open Edit/Add Game Rule AdvancedStreamEngine StreamEngine Setup Enable StreamEngine Dynamic Fragmentation Automatic ClassificationAutomatic Uplink Speed Measured Uplink Speed Priority Add/Edit StreamEngine Rule EnableSource IP Range Source Port Range Add/Edit Route AdvancedRouting Routes List Policy Wizard AdvancedAccess ControlAdd Policy Policy Table Web Filter Parameters Web Site AdvancedWEB FilterAdd/Edit Web Site Allowed Web Site List Filter Settings Mode Enable MAC Address FilterFilter Wireless Clients AdvancedMAC Address Filter Add/Edit MAC Address Filter Wired ClientsMAC Address List AdvancedFirewall NAT Endpoint Filtering Firewall Settings Enable SPIEndpoint Independent Address Restricted DMZ Host Enable DMZDMZ IP Address Rtsp Pptp Netmeeting FTPSIP Wake-On-LAN AdvancedInbound Filter Action Add/Edit Inbound Filter RuleInbound Filter Rules List Allow All AdvancedAdvanced Wireless WMM Enable 802.11d EnableExtra Wireless Protection WDS Enable Enable WAN Ping Respond Enable UPnPAdvancedNetwork UPnP AdvancedWISH Enable Multicast StreamsWAN Port Speed Multicast Streams Http Wish Host 1 IP Range Save/UpdateHost 1 Port Range Host 2 IP Range Wi-Fi Protected Setup Enable AdvancedWi-Fi Protected SetupLock Wireless Security Settings PIN Settings Add Wireless Device Wizard Reset PIN to DefaultCurrent PIN Generate New PIN Tools ToolsAdmin User Password Admin PasswordEnable Remote Management Remote Admin Port Enable Daylight Saving Time Configuration Current Router TimeToolsTime Time Zone Daylight Saving Offset Automatic Time Configuration Enable NTP ServerDST Start and DST End NTP Server Used ToolsSyslog Enable Logging to Syslog ServerSyslog Server IP Address ToolsEmail Settings Email Log When Full or on Schedule On Log Full Verify PasswordOn Schedule Load Settings From Local Hard Drive Save Settings To Local Hard DriveRestore To Factory Default Settings Reboot The Device ToolsFirmware Firmware UpgradeFirmware Information Check Online Upload ToolsDynamic DNS Timeout ToolsSystem Check ToolsSchedules Schedule Rules List Statistics and Active Sessions StatusDevice info PPPoE, PPTP, L2TP Connection Dhcp ConnectionBigPond Connection LAN Computers Signal StatusWirelessRate StatusRouting StatusLogs Apply Log Settings NowWhat to View View Levels Email Now RefreshSave Log StatusStatistics Internal StatusActive SessionsExternal NAT Dir StatusWISH SessionsOut Time Out Target Originator Established or closing TCP connections Ascii Adsl Bootp CAT DMZ Dhcp DSL DNSEAP GUI Icmp HttpsIeee Igmp ISP IPX LED LANLPR/LPD L2TP MIB MdixMppe MTU NTP NICOfdm OSI Radius PPPRIP Smtp RSASnmp Soho TCP SsidTCP/IP Tftp USB URLUTP Vlan Wisp WDSWlan WPA 802.11 Yagi antenna Technical Support