Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper S211, SP211, SPV211, SPV211S, SPV211E important safety instructions Models

Models: S211, SP211, SPV211, SPV211S, SPV211E

1 28

Download 28 pages 31.34 Kb

Page 1

Safety Instructions & Operator's Manual for

Safety Instructions & Operator's Manual for

21” ‘EASY LINE’

WALK BEHIND MOWERS

MODELS

S211

SP211

SPV211

SPV211S

SPV211E

MODEL NUMBER EXPLANATION

S

P

V

21

1

E

MODEL DESIGNATION

SELF-PROPELLED

VARIABLE SPEED

OPTION DESIGNATION

SERIES DESIGNATION

CUTTING WIDTH

S - ‘Easy Line’	V - Variable Speed Model	21 - 21” Cutting Width	S - Swivel Front Wheels

P - Self-Propelled Model		1 - Series 1	E - Electric Start

Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay particular attention to the "IMPORTANT SAFETY INSTRUCTIONS" on Pages 2 - 4. Remember that all power equip- ment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense!

NOTE: Specifications are correct at time of printing and are subject to change without notice.

*Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating Information’ on Page 4 for further information.

BRIGGS & STRATTON YARD POWER PRODUCTS GROUP COPYRIGHT © 2007, BRIGGS & STRATTON CORPORATION MILWAUKEE, WI, USA. ALL RIGHTS RESERVED.

MANUAL No. 7101295 (I.R. 1/3/2007) TP 100-5252-IR-WB-N

Image 1

Snapper S211, SP211, SPV211, SPV211S, SPV211E important safety instructions 21” ‘EASY LINE’ WALK BEHIND MOWERS, Models

Contents

21” ‘EASY LINE’ WALK BEHIND MOWERS Safety Instructions & Operators Manual forMODELS S211 SP211 SPV211 SPV211S SPV211EPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONMAINTENANCE AND STORAGE IMPORTANT SAFETY INSTRUCTIONSSAFE HANDLING OF GASOLINE OPERATIONMAINTENANCE AND STORAGE IMPORTANT SAFETY INSTRUCTIONSThe gross power rating labels for individual gas engine models meet or exceed SAE Society of Automotive Engineers code J1940 Small Engine Power & Torque Rating Procedure and rating performance has been obtained and corrected in accordance with SAE J1995 Revision 2002-05. Actual gross engine power may be lower and is affected by, but not limited to, ambient operating conditions and engine to engine variability. Given both the wide array of products on which engines are placed, and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment actual “on-site” or net horsepower. This difference is due to a variety of factors including, but not limited to, accessories air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc., application limitations, ambient operating conditions temperature, humidity, altitude, and engine to engine variability TABLE OF CONTENTS MODEL SPV211 SHOWN Section 1 - FAMILIARIZATION1.1 INTRODUCTION 1.2 NOMENCLATURE2.1 PRE-START CHECK LIST Section 2 - OPERATING INSTRUCTIONS2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Section 2 - OPERATING INSTRUCTIONS 2.5 HANDLE HEIGHT ADJUSTMENT2.2 STARTING & OPERATION 2.2.2. PROPELLING MOWER Self Propelled Models OnlySet all wheels in the highest cutting position Notch Section 2 - OPERATING INSTRUCTIONSSection 2 - OPERATING INSTRUCTIONS INSTALL LOCKSection 3 - MAINTENANCE 3. Replace rear cover Section 3 - MAINTENANCEEND VIEW OF BLADE ASSEMBLY Section 4 - REPAIR & ADJUSTMENTSNEW BLADE WEAR LIMIT NOTCH STARTS DANGEROUS CONDITION DO NOT USE ON MOWER REPLACE WITH NEW BLADE4.2 WHEEL DRIVE CONTROL ADJUSTMENT Section 4 - REPAIR & ADJUSTMENTSIMPORTANT INCORRECT ADJUSTMENT CAN CAUSE DAMAGE TO THE TRANSMISSION FIGURE 4.5aADJUSTMENT HOLES INCREASE MINIMUM GROUND SPEED DECREASE MINIMUM Section 4 - REPAIR & ADJUSTMENTSGROUND SPEED LEVER IN ‘SLOW’ POSITION SPRING HAS NO TENSION INNER NUT OUTER NUT BELT IS RELAXED2. Remove blade. Refer to Section “Blade Sharpening” Section 4 - REPAIR & ADJUSTMENTSBattery Condition Section 4 - REPAIR & ADJUSTMENTSTHREADED FASTENERS REAR COVER Section 4 - REPAIR & ADJUSTMENTSPROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE/REPLACEMENT PARTS SERVICEection3 SCHEDULE- OP RATING INSTRUCTIONS2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE Call the Snapper Customer Relations Center at SNAPPER PRODUCT REGISTRATION FORMPage Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone Safety Instructions & Operators Manual for21” ‘EASY LINE’ WALK BEHIND MOWERS MANUAL No. 7101295 I.R. 1/3/2007 TP 100-5252-IR-WB-N