Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper S211, SP211, SPV211, SPV211S, SPV211E SERVICEection3 SCHEDULE- OP RATING INSTRUCTIONS

Models: S211, SP211, SPV211, SPV211S, SPV211E

1 28

Download 28 pages 31.34 Kb

Page 20

SERVICEection3 SCHEDULE- OP RATING INSTRUCTIONS

ITEM	SERVICE	REF.	EACH	5	25	50	100	EACH
	PERFORMED		USE	HRS	HRS	HRS	HRS	SEASON

Engine Oil	Check Oil Level	Page 7	X

	Initial Oil Change	Page 11		X

	Periodic Oil Change	Page 11			X*

Air Pre-Cleaner	Clean Sponge Element	Engine Manual			X**

Air Cleaner	Clean or Replace	Engine Manual			X**

Spark Plug	Replace	Engine Manual					X

Engine Cooling	Clean Shroud & Fins	Engine Manual					X**
System
Drive Belt	Check for Wear and	Page 11, 16			X	X		X
	Tension
Mower Blade	Check for wear,	Page 13	X
	Damage &
	Replacement

Mower Deck	Clean Debris	Page 7	X
	Accumulation

Wheel Drive	Clean Debris	Page 12			X
Components	Accumulation; Check
	for Wear or Damage

Transmission	Check & Adjust	Page 14		X	X			X
Clutch Cable
Spring
Adjustment

Front Caster	Lubricate	Page 8			X
Bushing
(Swivel Wheel
Models Only)

*Change oil every 25 hours when operating under heavy load or high temperatures. ** Clean more often under dusty conditions or when air debris is present.

MAINTENANCE/REPLACEMENT PARTS

Blade Control Cable	7100074

Wheel Drive Control Cable (Self-Propelled Models)	7100263

Ground Speed Control Cable (Variable Speed Self-Propelled Models)	7100264

Cutter Blade (Double Wave)	7100242

Drive Belt (Self-Propelled Models)	7100058

Parts Manual for 21” Easy Line Walk Behind Mower	7006205

Parts Manual for 21” Easy Line Walk Behind Mower (Swivel-Wheel)	7006206

20

Image 20

Snapper S211, SP211, SPV211, SPV211S, SPV211E important safety instructions SERVICEection3 SCHEDULE- OP RATING INSTRUCTIONS

Contents

Safety Instructions & Operators Manual for 21” ‘EASY LINE’ WALK BEHIND MOWERSMODELS S211 SP211 SPV211 SPV211S SPV211EIMPORTANT SAFETY INSTRUCTIONS PROTECTION FOR CHILDRENSLOPE OPERATION PREPARATIONIMPORTANT SAFETY INSTRUCTIONS MAINTENANCE AND STORAGESAFE HANDLING OF GASOLINE OPERATIONThe gross power rating labels for individual gas engine models meet or exceed SAE Society of Automotive Engineers code J1940 Small Engine Power & Torque Rating Procedure and rating performance has been obtained and corrected in accordance with SAE J1995 Revision 2002-05. Actual gross engine power may be lower and is affected by, but not limited to, ambient operating conditions and engine to engine variability. Given both the wide array of products on which engines are placed, and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment actual “on-site” or net horsepower. This difference is due to a variety of factors including, but not limited to, accessories air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc., application limitations, ambient operating conditions temperature, humidity, altitude, and engine to engine variability IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE AND STORAGE TABLE OF CONTENTS Section 1 - FAMILIARIZATION MODEL SPV211 SHOWN1.1 INTRODUCTION 1.2 NOMENCLATURE2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Section 2 - OPERATING INSTRUCTIONS2.1 PRE-START CHECK LIST 2.5 HANDLE HEIGHT ADJUSTMENT Section 2 - OPERATING INSTRUCTIONS2.2 STARTING & OPERATION 2.2.2. PROPELLING MOWER Self Propelled Models OnlySection 2 - OPERATING INSTRUCTIONS Set all wheels in the highest cutting position NotchINSTALL LOCK Section 2 - OPERATING INSTRUCTIONSSection 3 - MAINTENANCE Section 3 - MAINTENANCE 3. Replace rear coverSection 4 - REPAIR & ADJUSTMENTS END VIEW OF BLADE ASSEMBLYNEW BLADE WEAR LIMIT NOTCH STARTS DANGEROUS CONDITION DO NOT USE ON MOWER REPLACE WITH NEW BLADESection 4 - REPAIR & ADJUSTMENTS 4.2 WHEEL DRIVE CONTROL ADJUSTMENTIMPORTANT INCORRECT ADJUSTMENT CAN CAUSE DAMAGE TO THE TRANSMISSION FIGURE 4.5aSection 4 - REPAIR & ADJUSTMENTS ADJUSTMENT HOLES INCREASE MINIMUM GROUND SPEED DECREASE MINIMUMGROUND SPEED LEVER IN ‘SLOW’ POSITION SPRING HAS NO TENSION INNER NUT OUTER NUT BELT IS RELAXEDSection 4 - REPAIR & ADJUSTMENTS 2. Remove blade. Refer to Section “Blade Sharpening”Section 4 - REPAIR & ADJUSTMENTS Battery ConditionSection 4 - REPAIR & ADJUSTMENTS THREADED FASTENERS REAR COVERTROUBLESHOOTING PROBLEMPROBABLE CAUSE CORRECTIVE ACTIONSERVICEection3 SCHEDULE- OP RATING INSTRUCTIONS MAINTENANCE/REPLACEMENT PARTS2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Call the Snapper Customer Relations Center atPage Safety Instructions & Operators Manual for Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone21” ‘EASY LINE’ WALK BEHIND MOWERS MANUAL No. 7101295 I.R. 1/3/2007 TP 100-5252-IR-WB-N