35
DAB1 DISTRIBUTED AUDIO SYSTEM
4) The DAB1 is factory-programmed for the following keypad functions:
•• PPRREESSSSaannyy SSOOUURRCCEEBBuuttttoonn::Turns the local zone ON with that source.
•• PPRREESSSS--AANNDD--HHOOLLDDaannyy SSOOUURRCCEEBBuuttttoonn::Activates PARTY MODE with that source for all zones.
•• PPRREESSSStthhee VVOOLLUUMMEEUUPP//DDOOWWNNBBuuttttoonnss::Raise and lower the volume in the local zone.
•• PPRREESSSStthhee MMUUTTEEBBuuttttoonn ((CC44663300 SSEE MMaaiinn KKeeyyppaadd));; PPRREESSSStthhee cceenntteerr ooff tthhee VVoolluummee UUPP//DDOOWWNNbbuuttttoonn ((DDAABB11
KKeeyyppaadd))::Mutes/un-Mute the local zone.
•• PPRREESSSS--AANNDD--HHOOLLDDtthheeMMUUTTEEBBuuttttoonn ((CC44663300 SSEE MMaaiinn KKeeyyppaadd));; PPRREESSSS--AANNDD--HHOOLLDDtthhee cceenntteerr ooff tthhee VVoolluummee
UUPP//DDOOWWNN bbuuttttoonn ((DDAABB11 KKeeyyppaadd))::Mutes/un-Mutes all zones designated for PARTY MODE.
•• PPRREESSSStthhee ZZOONNEEOOFFFF BBuuttttoonn::Turns the local zone OFF.
•• PPRREESSSS--AANNDD--HHOOLLDDtthhee ZZOONNEEOOFFFF BBuuttttoonn::Turns all zones designated for PARTY MODE OFF.
•• PPrreessss bbuuttttoonnss 11 tthhrroouugghh 1122 ((DDAABB11 KKeeyyppaadd))::Selects tuner presets 1 through 12.
•• PPRREESSSSbbuuttttoonnss 11 tthhrroouugghh 00 ((CC44663300 SSEE NNuummeerriicc KKeeyyppaadd))::Selects tuner presets 1 through 10.
•• PPRREESSSSbbuuttttoonnss ““––”” aanndd ““++”” ((CC44663300 SSEE NNuummeerriicc KKeeyyppaadd)):: Selects tuner presets 11 and 12.
5) A REPEAT UNTIL BUTTON ISRELEASED command in the PRESS level will defeat the PRESS-AND-HOLD level for that button.
Building Macros
Individual keypad button macros are programmed in the
MACRO EDITOR window. To open MACRO EDITOR:
1. Open the DEVICE screen (see
Figure 44,
opposite).
2. If the system has more than one DAB1, use the DEVICE
SELECTOR (see
Figure 41
) to select the one you want to
program. The Zone 1 programming screen for that
DAB1 will appear (see
Figure 45
).
• The Zone 1 programming screen will include one
set of VOLUMEUP/DOWN, MUTE and ZONE OFF
buttons and four sets of ZONE SOURCE CONTROL and
numeric buttons (one for each source). The source
names you selected on the SOURCE SETUP screen (see
Figure 43
, on page 33) will appear on the four
SOURCE buttons.
3. Right-click on the button you want to create or modify a
macro for.
• If the button already has been programmed with a
macro (a MACRO INDICATOR appears on the
button) select EDIT MACRO.
• If the button has not been programmed with a macro (no MACRO INDICATOR appears on the button) select CREATE MACRO.
The MACRO EDITOR screen will appear. See
Figure 46
, on page 36.