Specifications
Picture tube | 0.30 mm aperture grille pitch |
| 20Ê inches measured diagonally |
| |
Viewable image size | Approx. 388 × 292 mm (w/h) |
| (15 3/8 × 11 1/2 inches) |
| 19.1” viewing image |
Resolution | Horizontal: Max. 1280 dots |
| Vertical: Max. 1024 lines |
Standard image area Approx. 373 × 280 mm (w/h) | |
| (14 3/4 × 11 1/8 inches) |
| or |
| Approx. 350 × 280 mm (w/h) |
| (13 7/8 × 11 1/8 inches) |
Deflection frequency Horizontal: 30 to 86 kHz | |
| Vertical: 48 to 150 Hz |
AC input voltage/current | |
| 100 to 120 V, 50/60 Hz, 1.7 A |
| 220 to 240 V, 50 – 60 Hz, 1.2 A |
Power consumption | Max. 150 W |
Dimensions | Approx. 472 × 493.5 × 501 mm (w/h/d) |
| (18 5/8 × 19 1/2 × 19 3/4 inches) |
Mass | Approx. 29.5 kg (65 lb 1 oz) |
Pin assignment
Video input 1 connector (HD15) (Female)
The cable accepts RGB video signals (0.714
5 | 4 |
| 3 | 2 | 1 |
| 10 | 9 | 8 | 7 | 6 |
15 14 13 | 12 | 11 | |||
Pin No. | Signal | Pin No. | Signal | |
|
|
|
| |
1 | Red | 8 | Blue Ground | |
|
|
|
| |
2 | Green | 9 | DDC + 5V* | |
| (Composite |
|
| |
| 10 | Ground | ||
| Sync on Green) | |||
|
|
| ||
| 11 | — | ||
|
| |||
3 | Blue |
|
| |
12 | ||||
|
| |||
4 | — |
| Data (SDA)* | |
|
|
|
| |
5 | DDC Ground* | 13 | H. Sync | |
|
|
|
| |
6 | Red Ground | 14 | V. Sync | |
|
|
|
| |
7 | Green Ground | 15 | Data Clock (SCL)* |
*Display Data Channel (DDC) Standard by VESA.
Design and specifications are subject to change without notice.
Troubleshooting
This section may help you isolate a problem and as a result, eliminate the need to contact technical support, allowing continued productivity.
No picture
/If neither the u(power) indicator nor the POWER SAVING indicator is lit
—Check that the power cord is properly connected.
—Check that the u power switch is in the “on” position.
/If the POWER SAVING indicator is lit
—Check that your computer power switch is in the “on” position.
—The monitor will recover when you press any key on the keyboard of the computer.
—Check that the video cable is properly connected. (If your computer is a Macintosh system, the Macintosh adapter (supplied) is required.)
—Check that the 5 BNC's are connected in the right order (from power cord side: Red-
—Ensure that no pins are bent or pushed in the HD15 connector of the cable.
—Check that the video card is seated completely in a proper bus slot.
—Check that the video frequency range is within that specified for the monitor.
—If using a Macintosh system, check that the Macintosh adapter and the video signal cable are properly connected.
/If your system is the Windows 95
—Even if you select SONY for the maker on the device select screen, the model name
In this case, select the DDC standard monitor.
/If the u(power) and/or the POWER SAVING indicators are both flashing
—Turn the monitor off and on. If the indicators are not both flashing, the monitor is in the normal condition. If the indicator is still flashing, there is a potential monitor failure.
/If you do the above procedures and the monitor does not recover
—Unplug the video cable, then press and hold the ¬ + button for 2 seconds to display the color bars. If the color bars appear, the monitor is in the normal
condition. Then turn the monitor off and on by pressing the u power switch to return the monitor to the normal condition.
If the color bars do not appear, there is a potential monitor failure.
/If your computer is a Macintosh system and the Macintosh adapter has micro switches
—Check that the micro switches are properly set for your system. (See the adapter manual.)
EN
11
