Sony NSX-A707 manual Super Woofers 4 Jacks, VIDEO/AUX Jacks, MD Jacks, Line OUT Jacks

SUPER WOOFERS 4 JACKS

- CDDIGITALOUT (OPTICAL)

- VIDEOIAUX

- MD

– LINEOUT

- SUPER WOOFERS

‘SURROUND SPEAKERS

Refer to the operating instructions of the connected equipment for details,

●The connecting cords are not supplied. Obtain the necessary connecting cords.

●Consult your local Aiwa dealer for optional equipment.

.~gf*f**$8*~,&~j#*,~~,\~~*~*g~#g,i**da*Bs~&*!rneMwm,k,-#,x,*E*f@M,@*w*#*K~Jrm#nq@R!s%wmQ~~~,www.!s!8K

VIDEO/AUX JACKS

This unit can input analog sound signals through these jacks. Use a cable with RCA phono plugs to connect audio equipment (turntables, LD players, MD players, VCRs, TV, etc.).

Connect the red plug to the VIDEO/AUX R jack, and the white plug to the VIDEO/AUX L jack.

When connecting a turntable

Use an Aiwa turntable equipped with a built-in equalizer amplifier.

as8s*a**#J:#i*,?*&:*"l*.*.*w&"&a!-J&&#,:q,:;x%a#,8#&rw%FJr,m,r#i*.,trJ43:x**$!,,,.-:.?&e*A*?%=:~s%&wJc,’:,.

Connect optional powered sub woofers with built-in-amplifiers to the jacks.

For better FM reception, use of an outdoor antenna is recommended.

Connect the outdoor antenna to FM 75 Q terminals.

3’

MD JACKS

This jack is recommended to connect with an MD player.

Use a cable with RCA phono plugs.

Connect the red plug to the MD R jack, and the white plug to the

MD L jack.

POWER

W,C?3B%:...~~wfi~q~m:,g#*,J,m,~w,*fio#m#**8bm%,,w##jK*$..,A~&$ s&%,%-.8,.a%t,r%,*~:-w,*.!ks..,T#a.-.:*,,&*~m:$&$&..

LINE OUT JACKS

This unit can output analog sound signal through these jacks. Use a cable with RCA phono plugs to connect audio equipment with LINE IN (analog input) jacks.

Connect the red plug of a cable to LINE OUT R jack, and the white plug to LINE OUT L jack.

Do not connect an equipment to LINE OUT jacks and VIDEO/ AUX jacks simultaneously. Otherwise, noise is generated and malfunction occurs.

$38u$a.4?88Rtwwc4ti&*$@cm?v”’.,P’k”~mh*mzP.,8.,*.‘&?E*,,.xa#lEleE*@.~r+s-...-*a@v%#’.e..m*w:.2 -nrmrJ***,r*.m.r&-.:a

CD DIGITAL OUT (OPTICAL) JACK

This unit can output CD digital sound signals through this jack. Use an optical cable to connect digital audio equipment (DAT deck, MD recorder, etc.).

Remove the dust cap @ from the CD DIGITAL OUT (OPTICAL) jack. Then, connect an optical cable plug to the CD DIGITAL OUT (OPTICAL) jack.

To play a equipment connected to VIDEO/AUX jacks or MD jacks proceed as follows.

1 Press VIDEO/AUX or MD.

To riav the eaui~ment connected to VI DEO/AUX, press VIDEO/AUX. “VIDEO appears on the display.

To dav the equipment connected to MD, press MD. “MD” appears on the display.

2 Play the connected equipment.

To change a source name in the display

When VIDEO/AUX is pressed, “VIDEO is displayed initially, It can be changed to “AUX or “TV.

With the power on, press POWER while pressing VIDEO/AUX. Repeat the procedure to select one of the names.

To adjust the sound level of the external source

When the CD DIGITAL OUT (OPTICAL) jack is not being	When the sound level of the external source is much higher or
used
	much lower than that of other function sources, adjust it as follows.
Attach the supplied dust cap.
	1 Press VIDEO/AUX or MD and play the equipment.
*a.s.-~b%*?~z?.$e*~.K6.%r.*.&%3*Yaw8#~:sY&?&Rbze~?wa,%.:3,8?. .?em%;am.E&wq8%w*:e*cB%e8,m:&=i~w.-s:..*J:=#	2 Presss 4+ or ~ so that the sound level becomes the same
SURROUND SPEAKERS d JACKS	as that of other function sources.

Connect optional surround speakers with the 8 ohms to 16 ohms impedance to the jacks.

m

During recording, the sound level can not be adjusted.

25 ENGLISH