Manuals
/
Brands
/
Computer Equipment
/
Webcam
/
Sony
/
Computer Equipment
/
Webcam
Sony
PCS-1P, PCS-1
- page 55
1
55
78
78
Download
78 pages, 697.42 Kb
2-25
PCS-1/PCS-1P
(4)
Enter
“
LAN
”
in
“
Name:
”
, select any icon, and click the
“
OK
”
button.
(5)
Select
“
TCP/IP (Winsock)
”
in
“
Connect To
”
, enter the IP address of PCS-1/1P in
“
Host address:
”
,
and click the
“
OK
”
button.
Contents
Main
Page
Table of Contents
1. Installation
2. Maintenance
3. Compatibility in LAN Network
4. Technical Data
Section 1 Installation
1-1. Caution on Installation
1-1-1. Lay Out the Videoconferencing Room
Page
Page
Page
Page
1-1-2. Operating Environment
1-2. Flowchart of Installation
1-7
1-8
1-3. System Connections
1-3-1. When Used in LAN (100BASE-TX/10BASE-T)
1-9
1-3-2. When Used in ISDN
1-4. Initialization
1-4-1. Inserting Batteries into the Remote Commander
1-4-2. Turning On/Off the TV Monitor Together With the Communication Terminal
1-4-3. Adjust the Volume of a Monitor Television
1-4-4. Installing the Communication Terminal and Camera
1-4-5. Turning On
1-4-6. When the Power was First Turned on after Installation
Page
CancelPrevious
Save
1-17
1-5. System Setting
The contents of a setting menu are shown in the table below. Change the setting as required.
1-18
1-19
1-6. Flowchart of Opening Test
1-21
1-6-1. Outgoing Procedure of ISDN
1-22
1-23
1-6-2. Incoming Procedure of ISDN
1-6-3. Outgoing Procedure of LAN
1-24
1-25
1-6-4. Incoming Procedure of LAN
1-26
Section 2 Maintenance
2-1. Confirmation Procedure of Local Terminal Operation Using Self-Loop
2-2
2-2. Separation of Components
The main troubles that occur during failure are described in the table below.
2-3
1. The power is not turned on even if the power switch on the side panel is pressed.
2-4
2. The power is not turned on even if the power button of a remote controller is pressed.
2-5
3. The power is not turned on during automatic incoming. (ISDN)
2-6
4. The power is not turned on during automatic incoming. (LAN)
2-7
5. The power of a monitor television is not turned on during the power-on sequence.
2-8
6. The image from a camera is not displayed after the power is turned on.
2-9
7. No function can be operated using a remote controller.
2-10
8. The camera on the local side cannot be operated.
2-11
9. No line is connected. (ISDN)
2-12
10. No line is connected. (LAN)
2-13
11. No voice can be heard from the remote side after a line is connected.
2-14
12. No voice can be transmitted to the remote side after a line is connected.
SS-12
2-15
2-16
14. An image on the remote side is not displayed after a line is connected.
2-17
15. An image cannot be transmitted to the remote side after a line is connected.
2-3. Operation Log
Page
Page
Page
Page
Page
Page
Page
Page
Page
2-4. Updating of Software
2-4-1. Updating Using Memory Stick
2-5. Service Mode
Page
Page
Page
Section 3 Compatibility in LAN Network
3-1. Connection via Hub
Page
3-2. Connection via Router
Page
3-3. Connection via DHCP
Page
3-4. Connection via Gatekeeper
Page
3-5. Connection via DHCP and Gatekeeper
Page
4-1
Section 4 Technical Data
4-1. PCS-1/1P Port Number Used
4-1-1. During Opposed Connection (Specified Value)
4-1-3. During Use of Internal MCU Function (Specified Value)
4-2. Setting of PCS-1 and HUB