1-17

PCS-1/PCS-1P
1-5. System Setting

The contents of a setting menu are shown in the table below.

Change the setting as required.

Contents of setting
Select the line interface (LAN, ISDN, or voice telephone) used.
Select “On” when connecting using a bonding interface through which the
remaining lines can also be connected by only dialing one line when multiple
ISDN lines are used. Select “Auto” when automatically adjusting to the remote
side.
Select the number of ISDN lines used during outgoing of bonding.
!B, 2B, 3B, 4B, 5B, 6B, 8B, or 12B channel can be selected.
Set the bandwidth (1 to 1920) when communicating via LAN.
Set the prefix number used when connecting using an ISDN line.
Select the communication rate (Auto or 56K) when connecting using an ISDN
line.
In a few countries (America, etc.) and regions, two types of rates (64 Kbps and 56
Kbps) are used.
Usually, select “Auto” as the communication rate of ISDN.
Select a video coding system.
Select the maximum number of video transmission frames (15 fps or 30 fps).
Select an audio coding system.
Set to “On” when controlling the camera on the remote side. Set to “Off” when
not controlling it.
Set to “On” when making the data conference conforming to T.120 using
NetMeeting. Set to “Off” when not making it.
Set the prefix (outgoing number).
Select the voice compression system during voice meeting.
Set to “On” when you want to have outgoing attributes for each dial list. Set to
“Off” when you do not want.
Set to “On” when recording the user name in a communication log before
communication. Set to “Off” when not recording it.
Set to “On” when making a conference using an internal MCU (multipoint
conference) function. Set to “Off” when not making it.
Set to “Divide” when displaying the connected terminal in the broadcasting
display mode of a multipoint conference by division. Set to “Audio detect” when
displaying the terminal with the highest volume in the participated terminals.
Select the number of ISDN lines for each sub-terminal of a multipoint conference.
Enter the bandwidth when a multipoint conference is made using LAN. The
bandwidth can be set in the range of 1 kHz to 1920 kHz.
Select the communication rate (Auto or 56 K) when connecting using an ISDN
line. In a few countries (America, etc.) and regions, two types of rates (64 Kbps
and 56 Kbps) are used.
Usually, select “Auto” as the communication rate of ISDN.
Select a video coding system.
Select an audio coding system.
Set to “On” when displaying the terminal name at a connection point on the
monitor screen during disconnection. Set to “Off” when not displaying it.
Set to “On” when controlling the camera on the remote side. Set to “Off” when
not controlling it.
Enter the terminal name to be notified in external MCU.
Set to “On” when using a dual monitor function with the two monitors connected.
Select whether a signal should be output to the monitor connected to which output
terminal. When “Dual monitor” is set to “On”, the menu is changed to “Sub-
monitor output”. Select whether a signal should be output to the sub-monitor
connected to which output terminal.
Set to “On” when using the standby mode. Set to “Off” when not using it.
Set the time (1 to 99 minutes) required until the unit is put into the standby mode
when the standby mode is “On”.
Set to “On” when displaying the talking time. Set to “Off” when not displaying it.
Set to “On” when using optional data solution box PCS-DSB1. Set to “Off” when
not using it.
Set to “On” when registering the remote user in an address book after a conference
is terminated. Set to “Off” when not registering it.
Enter the IP address of the computer used when the data conference conforming to
T.120 is made using NetMeeting.
Initial value
LAN
Auto
12B
1024
None
Auto
All capabilities
15 fps
All capabilities
On
Off
Blank
Auto
Off
Off
Off
Divide
2Bx5
1024
Auto
All capabilities
All capabilities
On
On
Blank
Off
Video terminal of
main unit
Off
On
On
On
Blank
Outgoing setting
Multipoint
General setting
Line type
Bonding
Number of lines used
LAN band used
Prefix selection
Restricted network
Video system
Number of video frames
Audio system
Remote camera control
T.120 data
Prefix -A/-B/-C
Voice telephone
Detail setting
Name entry
Multipoint mode
Broadcasting mode
Number of lines used
LAN band used
Restricted network
Video system
Audio system
Terminal name display
Remote camera control
Terminal name
Dual monitor
Monitor output
(Sub-monitor output)
Standby mode
Standby time
Passage time display
Use of DSB
List registration after
conference termination
T.120 PC address
Item
A multipoint setting
menu can be set
only when optional
H.320 MCU
software or H.323
MCU software is
installed.