Sony PCS-1P, PCS-1 2-15

2-15

PCS-1/PCS-1P

Is video input

properly set?

Is “Object” selected

as video input?

YES

Press input selector button of remote controller

and select input properly using joystick.

SS-13

Is video signal output

from equipment connected

to AUX1 and AUX2

terminals?

YES Connected equipment is defective.

Communication terminal is defective.

Is power

PCS-DS150 on?

YES Turn on power of PCS-DS150.

Does

obstacle exist

between infrared light

emitter of PCS-DS150 and infrared

photosensor of

communication

terminal?

Remove obstacle and adjust so

that light emitter is linear with

photosensor.

YES

Communication terminal or

PCS-DS150 is defective.

13. No video input (object, AUX1, or AUX2) image can be displayed. The image of a camera isdisplayed.

Contents

Main Page Table of Contents 1. Installation 2. Maintenance 3. Compatibility in LAN Network 4. Technical Data Section 1 Installation 1-1. Caution on Installation 1-1-1. Lay Out the Videoconferencing Room Page Page Page Page 1-1-2. Operating Environment 1-2. Flowchart of Installation 1-7 1-8 1-3. System Connections 1-3-1. When Used in LAN (100BASE-TX/10BASE-T) 1-9 1-3-2. When Used in ISDN 1-4. Initialization 1-4-1. Inserting Batteries into the Remote Commander 1-4-2. Turning On/Off the TV Monitor Together With the Communication Terminal 1-4-3. Adjust the Volume of a Monitor Television 1-4-4. Installing the Communication Terminal and Camera 1-4-5. Turning On 1-4-6. When the Power was First Turned on after Installation Page CancelPrevious Save 1-17 1-5. System Setting The contents of a setting menu are shown in the table below. Change the setting as required. 1-18 1-19 1-6. Flowchart of Opening Test 1-21 1-6-1. Outgoing Procedure of ISDN 1-22 1-23 1-6-2. Incoming Procedure of ISDN 1-6-3. Outgoing Procedure of LAN 1-24 1-25 1-6-4. Incoming Procedure of LAN 1-26 Section 2 Maintenance 2-1. Confirmation Procedure of Local Terminal Operation Using Self-Loop 2-2 2-2. Separation of Components The main troubles that occur during failure are described in the table below. 2-3 1. The power is not turned on even if the power switch on the side panel is pressed. 2-4 2. The power is not turned on even if the power button of a remote controller is pressed. 2-5 3. The power is not turned on during automatic incoming. (ISDN) 2-6 4. The power is not turned on during automatic incoming. (LAN) 2-7 5. The power of a monitor television is not turned on during the power-on sequence. 2-8 6. The image from a camera is not displayed after the power is turned on. 2-9 7. No function can be operated using a remote controller. 2-10 8. The camera on the local side cannot be operated. 2-11 9. No line is connected. (ISDN) 2-12 10. No line is connected. (LAN) 2-13 11. No voice can be heard from the remote side after a line is connected. 2-14 12. No voice can be transmitted to the remote side after a line is connected. SS-12 2-15 2-16 14. An image on the remote side is not displayed after a line is connected. 2-17 15. An image cannot be transmitted to the remote side after a line is connected. 2-3. Operation Log Page Page Page Page Page Page Page Page Page 2-4. Updating of Software 2-4-1. Updating Using Memory Stick 2-5. Service Mode Page Page Page Section 3 Compatibility in LAN Network 3-1. Connection via Hub Page 3-2. Connection via Router Page 3-3. Connection via DHCP Page 3-4. Connection via Gatekeeper Page 3-5. Connection via DHCP and Gatekeeper Page 4-1 Section 4 Technical Data 4-1. PCS-1/1P Port Number Used 4-1-1. During Opposed Connection (Specified Value) 4-1-3. During Use of Internal MCU Function (Specified Value) 4-2. Setting of PCS-1 and HUB