Sony PCS-1P, PCS-1 1-25

1-25

PCS-1/PCS-1P

Item

Operation

The remote side makes a response.

Disconnection

Press the connect/disconnect ( /) button of a remote

controller. A confirmation message on whether to

disconnect a line is then displayed.

Select “OK” using a ← or → button of a remote controller

and press the decide button, or press the connect/disconnect

( / ) button of a remote controller again.

Screen Remarks (Confirmation item)

The ON LINE lamp (blue) lights.

“Start meeting” is displayed, and the

remote voice and image are heard and

displayed from the monitor television.

The line is disconnected and the

conference is terminated. The current

display returns to a launcher menu.

Meeting starts!

Picture on

the local site

Picture on

the remote

site

Contents

Main Page Table of Contents 1. Installation 2. Maintenance 3. Compatibility in LAN Network 4. Technical Data Section 1 Installation 1-1. Caution on Installation 1-1-1. Lay Out the Videoconferencing Room Page Page Page Page 1-1-2. Operating Environment 1-2. Flowchart of Installation 1-7 1-8 1-3. System Connections 1-3-1. When Used in LAN (100BASE-TX/10BASE-T) 1-9 1-3-2. When Used in ISDN 1-4. Initialization 1-4-1. Inserting Batteries into the Remote Commander 1-4-2. Turning On/Off the TV Monitor Together With the Communication Terminal 1-4-3. Adjust the Volume of a Monitor Television 1-4-4. Installing the Communication Terminal and Camera 1-4-5. Turning On 1-4-6. When the Power was First Turned on after Installation Page CancelPrevious Save 1-17 1-5. System Setting The contents of a setting menu are shown in the table below. Change the setting as required. 1-18 1-19 1-6. Flowchart of Opening Test 1-21 1-6-1. Outgoing Procedure of ISDN 1-22 1-23 1-6-2. Incoming Procedure of ISDN 1-6-3. Outgoing Procedure of LAN 1-24 1-25 1-6-4. Incoming Procedure of LAN 1-26 Section 2 Maintenance 2-1. Confirmation Procedure of Local Terminal Operation Using Self-Loop 2-2 2-2. Separation of Components The main troubles that occur during failure are described in the table below. 2-3 1. The power is not turned on even if the power switch on the side panel is pressed. 2-4 2. The power is not turned on even if the power button of a remote controller is pressed. 2-5 3. The power is not turned on during automatic incoming. (ISDN) 2-6 4. The power is not turned on during automatic incoming. (LAN) 2-7 5. The power of a monitor television is not turned on during the power-on sequence. 2-8 6. The image from a camera is not displayed after the power is turned on. 2-9 7. No function can be operated using a remote controller. 2-10 8. The camera on the local side cannot be operated. 2-11 9. No line is connected. (ISDN) 2-12 10. No line is connected. (LAN) 2-13 11. No voice can be heard from the remote side after a line is connected. 2-14 12. No voice can be transmitted to the remote side after a line is connected. SS-12 2-15 2-16 14. An image on the remote side is not displayed after a line is connected. 2-17 15. An image cannot be transmitted to the remote side after a line is connected. 2-3. Operation Log Page Page Page Page Page Page Page Page Page 2-4. Updating of Software 2-4-1. Updating Using Memory Stick 2-5. Service Mode Page Page Page Section 3 Compatibility in LAN Network 3-1. Connection via Hub Page 3-2. Connection via Router Page 3-3. Connection via DHCP Page 3-4. Connection via Gatekeeper Page 3-5. Connection via DHCP and Gatekeeper Page 4-1 Section 4 Technical Data 4-1. PCS-1/1P Port Number Used 4-1-1. During Opposed Connection (Specified Value) 4-1-3. During Use of Internal MCU Function (Specified Value) 4-2. Setting of PCS-1 and HUB