Sony PCS-1P, PCS-1 3-3. Connection via DHCP

3-5

PCS-1/PCS-1P

Teleconference

terminal A Teleconference

terminal B

DHCP

server A DHCP

server B

Router Router

LAN1 LAN2

3-3. Connection via DHCP

Example of system

When a call is initiated from teleconference terminal A to teleconference terminal B.

1. The LAN set menu of teleconference terminal B is set as described below.

DHCP mode: ON

Host name: Enter any name.

IP address: Blank

Network mask: Blank

Gateway address: Blank

DNS address: Blank

Gatekeeper used: OFF

Gatekeeper address: Blank

User name: Blank

User number: Blank

SNMP service: OFF

Trap transmission destination: Blank

Community name: public

Description of device: Videoconference Device

Installation place: Blank

Contact of administrator: Blank

NAT setting: OFF

NAT address: Blank

Packet retransmission request: Blank

Optimum rate control: OFF (Set to ON when a packet loss occurs frequently.)

Port number used: Specified value (Set to “User setting” when a port number is specified

by the network administrator.)

TCP port number: 2253 (Enter the port number specified by the network administrator

when the port number used is set to “User setting”.)

UDP port number: 49152 (Enter the port number specified by the network administrator

when the port number used is set to “User setting”.)

2. Confirm that the IP address displayed in the launcher menu of teleconference terminal B is

192.100.20.20.

Contents

Main Page Table of Contents 1. Installation 2. Maintenance 3. Compatibility in LAN Network 4. Technical Data Section 1 Installation 1-1. Caution on Installation 1-1-1. Lay Out the Videoconferencing Room Page Page Page Page 1-1-2. Operating Environment 1-2. Flowchart of Installation 1-7 1-8 1-3. System Connections 1-3-1. When Used in LAN (100BASE-TX/10BASE-T) 1-9 1-3-2. When Used in ISDN 1-4. Initialization 1-4-1. Inserting Batteries into the Remote Commander 1-4-2. Turning On/Off the TV Monitor Together With the Communication Terminal 1-4-3. Adjust the Volume of a Monitor Television 1-4-4. Installing the Communication Terminal and Camera 1-4-5. Turning On 1-4-6. When the Power was First Turned on after Installation Page CancelPrevious Save 1-17 1-5. System Setting The contents of a setting menu are shown in the table below. Change the setting as required. 1-18 1-19 1-6. Flowchart of Opening Test 1-21 1-6-1. Outgoing Procedure of ISDN 1-22 1-23 1-6-2. Incoming Procedure of ISDN 1-6-3. Outgoing Procedure of LAN 1-24 1-25 1-6-4. Incoming Procedure of LAN 1-26 Section 2 Maintenance 2-1. Confirmation Procedure of Local Terminal Operation Using Self-Loop 2-2 2-2. Separation of Components The main troubles that occur during failure are described in the table below. 2-3 1. The power is not turned on even if the power switch on the side panel is pressed. 2-4 2. The power is not turned on even if the power button of a remote controller is pressed. 2-5 3. The power is not turned on during automatic incoming. (ISDN) 2-6 4. The power is not turned on during automatic incoming. (LAN) 2-7 5. The power of a monitor television is not turned on during the power-on sequence. 2-8 6. The image from a camera is not displayed after the power is turned on. 2-9 7. No function can be operated using a remote controller. 2-10 8. The camera on the local side cannot be operated. 2-11 9. No line is connected. (ISDN) 2-12 10. No line is connected. (LAN) 2-13 11. No voice can be heard from the remote side after a line is connected. 2-14 12. No voice can be transmitted to the remote side after a line is connected. SS-12 2-15 2-16 14. An image on the remote side is not displayed after a line is connected. 2-17 15. An image cannot be transmitted to the remote side after a line is connected. 2-3. Operation Log Page Page Page Page Page Page Page Page Page 2-4. Updating of Software 2-4-1. Updating Using Memory Stick 2-5. Service Mode Page Page Page Section 3 Compatibility in LAN Network 3-1. Connection via Hub Page 3-2. Connection via Router Page 3-3. Connection via DHCP Page 3-4. Connection via Gatekeeper Page 3-5. Connection via DHCP and Gatekeeper Page 4-1 Section 4 Technical Data 4-1. PCS-1/1P Port Number Used 4-1-1. During Opposed Connection (Specified Value) 4-1-3. During Use of Internal MCU Function (Specified Value) 4-2. Setting of PCS-1 and HUB