Manuals / Brands / Computer Equipment / Webcam / Sony / Computer Equipment / Webcam

Sony PCS-1P, PCS-1 2-5, 3. The power is not turned on during automatic incoming. (ISDN)

1 78

Download 78 pages, 697.42 Kb

2-5

PCS-1/PCS-1P

YES

Turn on power switch on side panel.

Connect them properly.

YES

Is power

turned on when I/O

button of remote controller

is pressed?

Are

communication terminal

and ISDN unit properly

connected?

Does POWER

(amber) lamp light?

SS-03

Communication terminal is defective.

Proceed to “2. The power is not

turned on even if the I/O button of a

remote controller is pressed”.

Connect it properly.

YES

Is ISDN

modular cable properly

connected to IDSN

unit?

ISDN unit or ISDN

line is defective.

YES

Does STATUS

lamp of terminal, to which

ISDN modular cable of ISDN

unit is connected,

light in red?

Communication terminal or

ISDN unit is defective.

YES

Does STATUS

lamp of ISDN unit blink

in green?

3. The power is not turned on during automatic incoming. (ISDN)

Contents

Main Page Table of Contents 1. Installation 2. Maintenance 3. Compatibility in LAN Network 4. Technical Data Section 1 Installation 1-1. Caution on Installation 1-1-1. Lay Out the Videoconferencing Room Page Page Page Page 1-1-2. Operating Environment 1-2. Flowchart of Installation 1-7 1-8 1-3. System Connections 1-3-1. When Used in LAN (100BASE-TX/10BASE-T) 1-9 1-3-2. When Used in ISDN 1-4. Initialization 1-4-1. Inserting Batteries into the Remote Commander 1-4-2. Turning On/Off the TV Monitor Together With the Communication Terminal 1-4-3. Adjust the Volume of a Monitor Television 1-4-4. Installing the Communication Terminal and Camera 1-4-5. Turning On 1-4-6. When the Power was First Turned on after Installation Page CancelPrevious Save 1-17 1-5. System Setting The contents of a setting menu are shown in the table below. Change the setting as required. 1-18 1-19 1-6. Flowchart of Opening Test 1-21 1-6-1. Outgoing Procedure of ISDN 1-22 1-23 1-6-2. Incoming Procedure of ISDN 1-6-3. Outgoing Procedure of LAN 1-24 1-25 1-6-4. Incoming Procedure of LAN 1-26 Section 2 Maintenance 2-1. Confirmation Procedure of Local Terminal Operation Using Self-Loop 2-2 2-2. Separation of Components The main troubles that occur during failure are described in the table below. 2-3 1. The power is not turned on even if the power switch on the side panel is pressed. 2-4 2. The power is not turned on even if the power button of a remote controller is pressed. 2-5 3. The power is not turned on during automatic incoming. (ISDN) 2-6 4. The power is not turned on during automatic incoming. (LAN) 2-7 5. The power of a monitor television is not turned on during the power-on sequence. 2-8 6. The image from a camera is not displayed after the power is turned on. 2-9 7. No function can be operated using a remote controller. 2-10 8. The camera on the local side cannot be operated. 2-11 9. No line is connected. (ISDN) 2-12 10. No line is connected. (LAN) 2-13 11. No voice can be heard from the remote side after a line is connected. 2-14 12. No voice can be transmitted to the remote side after a line is connected. SS-12 2-15 2-16 14. An image on the remote side is not displayed after a line is connected. 2-17 15. An image cannot be transmitted to the remote side after a line is connected. 2-3. Operation Log Page Page Page Page Page Page Page Page Page 2-4. Updating of Software 2-4-1. Updating Using Memory Stick 2-5. Service Mode Page Page Page Section 3 Compatibility in LAN Network 3-1. Connection via Hub Page 3-2. Connection via Router Page 3-3. Connection via DHCP Page 3-4. Connection via Gatekeeper Page 3-5. Connection via DHCP and Gatekeeper Page 4-1 Section 4 Technical Data 4-1. PCS-1/1P Port Number Used 4-1-1. During Opposed Connection (Specified Value) 4-1-3. During Use of Internal MCU Function (Specified Value) 4-2. Setting of PCS-1 and HUB