U01 | OUTPUT |
|
| TOP |
LCD | BRIGHT | <L> | : | 0 |
LCD | BRIGHT | <H> | : | 0 |
LCD | COLOR |
| : | 0 |
PC | REMOTE |
| : | DSABL |
REAR BNC OUT SEL: | VBS |
Item | Description |
|
|
LCD BRIGHT <L> | Adjusts the LCD brightness when the |
| LCD switch is in the L position. |
|
|
LCD BRIGHT <H> | Adjusts the LCD brightness when the |
| LCD switch is in the H position. |
|
|
LCD COLOR | Adjusts the color saturation of the LCD. |
|
|
i.LINK SBP2 | Selects whether or not to use the |
MODE | i.LINK connector SBP2 interface. |
|
|
REAR BNC OUT | Selects the type of the video signal to |
SEL | be output from the VIDEO OUT |
| connector. |
| SDI : Outputs the SDI signal. When |
| SDI is selected, connect the |
| VIDEO OUT connector to the SDI |
| IN connector of the video monitor. |
| VBS: Outputs the analog composite |
| video signal. When VBS is |
| selected, connector the VIDEO |
| OUT connector to the VIDEO IN |
| connector of the video monitor. |
| This setting allows you to save the |
| power. |
|
|
3 Turn the MENU knob to move the b mark to “REAR BNC OUT SEL”, and press the MENU knob.
The b mark on the left of “REAR BNC OUT SEL” changes to a z mark and the z mark on the left of the setting changes to a ? mark.
4 Turn the MENU knob to change the desired setting, and press the MENU knob.
The z mark on the left of the selected item changes to a b mark and the ? mark on the left of the setting changes to a z mark.
5 To end the menu operation, set the MENU ON/OFF switch to OFF or close the cover of the menu operating section.
To enable DV stream outputProceed as follows.
1 Holding down the MENU knob, move the MENU ON/ OFF switch to ON.
The TOP menu appears.
2 Turn the MENU knob to move the b mark to “OPERATION”, then press the MENU knob.
If this is the first time the OPERATION menu has been displayed, the CONTENTS page appears. If the menu has been used before, the last accessed page appears.
3 If the CONTENTS page is displayed, turn the MENU knob to move the b mark to POWER SAVE, then press the MENU knob.
If a different page is displayed, turn the MENU knob until the POWER SAVE page appears, then press the MENU knob.
The POWER SAVE page appears. The current settings appear on the right side of each item.
04 POWER | SAVE |
| TOP |
i.LINK OUT |
| : | DSABL |
REC AUDIO | OUT | : | EE |
NETWORK/THUMB | : | SAVE |
Item | Setting |
|
|
i.LINK OUT | Enable or disable i.LINK (AV/C) OUT. |
|
|
REC AUDIO OUT | Select whether to output |
| or no audio from the AUDIO OUT |
| connector during recording. |
|
|
NETWORK/ | Select whether to permanently enable |
THUMB | the |
| display, or to disable them in power |
| saving mode. |
|
|
4 Move the b mark to “i.LINK OUT”, then press the MENU knob.
The b mark changes to a z mark, and the z mark changes to a ? mark.
5 Turn the MENU knob to select “ENABL”, then press the MENU knob.
The setting is confirmed. The z mark changes to a b mark and the ? mark changes to a z mark.
6 To end the menu operation, set the MENU ON/OFF switch to OFF.
Notes
•As the i.LINK cable, use an
•DV streams are not output when the i.LINK DV IN/ OUT S400 connector is set to input.
Settings Detailed and Displays Menu 7 Chapter
123 | |
|
|