MAIN BOARD IC1101 CXD9927R (RF AMP, SERVO DSP, HDMI TRANSMITTER)
Pin No. | Pin Name | I/O |
|
| Description |
| |
1 | OSC | O | RF offset cancellation capacitor connecting terminal |
| |||
2 | RFGC | O | RF AGC loop capacitor connecting Not used |
| |||
3 | IREF | I | Reference current input terminal |
|
|
|
|
4 | AVDD3 | - | Power supply terminal (+3.3V) |
|
|
|
|
5 | AGND | - | Ground terminal |
|
|
|
|
6 | DVDA | I | AC coupled input path A |
|
|
|
|
7 | DVDB | I | AC coupled input path B |
|
|
|
|
8 | DVDC | I | AC coupled input path C |
|
|
|
|
9 | DVDD | I | AC coupled input path D |
|
|
|
|
10 | DVDRF IP | I | AC coupled super audio CD RF signal input from the optical | ||||
11 | MA | I | DC coupled |
|
| ||
12 | MB | I | DC coupled |
|
| ||
13 | MC | I | DC coupled |
|
| ||
14 | MD | I | DC coupled |
|
| ||
15 | SA | I | DC coupled | Not used |
| ||
16 | SB | I | DC coupled | Not used |
| ||
17 | TNI | I | 3 beam satellite PD signal negative input from the optical | ||||
18 | TPI | I | 3 beam satellite PD signal positive input from the optical | ||||
19, 20 | MDI1, MDI2 | I | Laser power monitor input from the optical | ||||
21 | LDO2 | O | Laser diode drive signal output to the optical | ||||
22 | LDO1 | O | Laser diode drive signal output to the optical | ||||
23 | SVDD3 | - | Power supply terminal (+3.3V) |
|
|
|
|
24 | CSO | O | Central servo signal output terminal | Not used |
| ||
25 | RFLVL | O | RFRP low pass output terminal | Not used |
| ||
26 | SGND | - | Ground terminal |
|
|
|
|
27 | V2REFO | - | Reference voltage (+2.8V) output terminal |
|
| ||
28 | V2O | - | Reference voltage (+2V) output to the optical | ||||
29 | VREFO | O | Reference voltage (+1.4V) output terminal |
|
| ||
30 | FEO | O | Focus error monitor output terminal | Not used |
| ||
31 | TEO | O | Tracking error monitor output terminal | Not used |
| ||
32 | TEZISLV | O | O Slice level of tracking error signal output terminal | Not used | |||
33 | OP_OUT | O | Output to the internal operational amplifier | Not used |
| ||
34 | OP_INN | I | Negative input from the internal operational amplifier | Not used | |||
35 | OP_INP | I | Positive input from the motor driver |
|
|
| |
36 | DMO | O | Spindle motor control signal output to the motor driver | ||||
37 | FMO | O | Sled motor control signal output to the motor driver |
| |||
38 | TROPENPWM | O | Loading motor control signal output terminal |
| |||
39 | IOPMON | I | Power monitor terminal |
|
|
|
|
40 | TRO | O | Tracking coil control signal output to the coil driver |
| |||
41 | FOO | O | Focus coil control signal output to the coil driver |
| |||
42 | AGND18 | - | Ground terminal |
|
|
|
|
43 | AVDD18 | - | Power supply terminal (+1.8V) |
|
|
|
|
44 | USB_DP | I/O | Not used |
| |||
45 | USB_DM | I/O | Not used |
| |||
46 | USB_VDD3 | - | Power supply terminal (+3.3V) |
|
|
|
|
47 | USB_VSS | - | Ground terminal |
|
|
|
|
48 | PAD_VRT | - | Not used |
|
|
|
|
49 | USB_VDD18 | - | Power supply terminal (+1.8V) |
|
|
|
|
50 | USB_VSS | - | Ground terminal |
|
|
|
|
51 | DIR_ERROR | O | PLL lock error signal and data error flag output termnal Not used | ||||
52 | DIR_AUDIO | O | PCM audio data output termnal | Not used |
| ||
53 | LIMITSW | I | Limit detection switch input terminal |
|
|
| |
54 | MSW | O | CD/super audio CD selection signal output terminal | "L": CD, "H": super audio CD | |||
55 | DVDD18 | - | Power supply terminal (+1.8V) |
|
|
|
|
56 to 64 | HA2 to HA8, HA18, | O | Address signal output to the flash ROM |
|
| ||
HA19 |
|
| |||||
|
|
|
|
|
|
| |
65 | DVDD3 | - | Power supply terminal (+3.3V) |
|
|
|
|
66 | XWR | O | Write enable signal output to the flash ROM |
| |||
67 to 75 | HA16 to HA9, HA20 | O | Address signal output to the flash ROM |
|
|
43