Sony VPL-VW60 Input, System, General

Specifications

System

Projection system

SXRD panel, 1 lens, projection system

LCD panel 0.61-inch (15.4 mm) SXRD panel 6,220,800 pixels (2,073,600 pixels

⋅3)

Lens	1.8 times zoom lens (motorized)
	f18.7 to 33.7 mm/F2.54 to 3.53
Lamp	200 W Ultra High Pressure Lamp
Projection picture size
	40 to 300 inches (1,016 mm to
	7,620 mm) (measured diagonally)
Color system	NTSC3.58/PAL/SECAM/NTSC4.43/
	PAL-M/PAL-N/PAL60 system,
	switched automatically/manually
	(PAL60 system not switched

manually) Acceptable video signals

15 kHz RGB/component 50/60 Hz, Progressive component 50/60 Hz, DTV (480/60i, 576/50i, 480/ 60p, 576/50p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/48i), 1080/60p (HDMI input only), 1080/50p (HDMI input only), 1080/24p (HDMI input only), Composite video, Y/C video

Acceptable computer signals fH: 19 to 72 kHz fV: 48 to 92 Hz

Maximum resolution 1920⋅ 1080, fV: 60 Hz

Input

Video input VIDEO: phono type Composite video: 1 Vp-p±2 dB sync negative (75 ohms terminated)

S VIDEO: Y/C mini DIN 4-pin type

Y (luminance): 1 Vp-p±2 dB sync negative (75 ohms terminated)

C(chrominance): burst 0.286 Vp- p ±2 dB (NTSC)

(75 ohms terminated), or burst 0.3 Vp-p±2 dB (PAL) (75 ohms terminated)

Y PB/CB PR/CR

Component: phono type

Y with Sync: 1 Vp-p±2dB sync negative (75 ohms terminated)

	PB/CB: 0.7 Vp-p±2dB (75 ohms
	terminated)
	PR/CR: 0.7 Vp-p±2 dB (75 ohms
	terminated)
HDMI	Digital RGB/Y CB (PB) CR (PR)
INPUT A	HD D-sub 15-pins
	Analog RGB/component:
	R/CR (PR): 0.7 Vp-p±2 dB
	(75 ohms terminated)
	G: 0.7 Vp-p±2 dB
	(75 ohms terminated)
	G with sync/Y: 1 Vp-p±2 dB sync
	negative (75 ohms terminated)
	B/CB (PB): 0.7 Vp-p±2 dB
	(75 ohms terminated)
	SYNC/HD: Composite sync input:
	TTL level, positive/ negative
	Horizontal sync input: TTL level,
	positive/negative
	VD: Vertical sync input: TTL
	level, positive/negative
TRIGGER	Minijack
	Power on: DC 12 V, output
	impedance: 4.7 kilohms
	Power off: 0 V
REMOTE	RS-232C: D-sub 9-pins (female)

General

Dimensions	395 ⋅ 173.5 ⋅ 471.4 mm
	(15 5/8 ⋅ 6 7/8 ⋅ 18 5/8 inches) (w/
	h/d)
Mass	Approx. 11 kg (24 lb 4 oz)

Power requirements

AC 100 to 240 V, 1.3 to 3.0 A, 50/60 Hz

Power consumption Max. 300 W

Standby mode: 8 W

Standby mode (low): 0.5 W Operating temperature

5°C to 35°C (41°F to 95°F) Operating humidity

35% to 85% (no condensation) Storage temperature

–20°C to +60°C (–4°F to +140°F) Storage humidity

10% to 90%

62

Contents

VPL-VW60 For customers in the USA Declaration of Conformity Disposal of Used Lamp For customers in the United States For customers in Europe Trademark Information Page Table of Contents Location of Controls Connections and Preparations Projecting Others On safety On preventing internal heat buildup Caution On repacking Location of Controls Page Page Connections and Preparations Before Setting Up the Projector Improper use Do not do any of the following while using the projector Blocking the ventilation holes Tip Tilting front/rear and left/right Positioning the Projector and a screen When using the 16:9 aspect ratio screen When using the 4:3 aspect ratio screen (projecting a 4:3 picture) 2 Position the projector so that the lens is parallel to the screen Top view Connecting to a VCR Page To connect to a VCR equipped with the S video connector or video connector Connecting to a Computer Page 2 Press the ?/1 (ON/STANDBY) switch to turn on the projector 3 Turn on the equipment connected to the projector 4 Press INPUT to project the picture on the screen 5 Adjust the vertical picture position 6 Adjust the picture size 7 Adjust the focus To adjust the tilt of the installation surface 1 Press MENU 2 Press M/m to select the Setup menu, and press , or 3 Press M/m to select “Language,” and press , or 4 Press M/m/</, to select a language, and press To clear the menu Projecting Turning Off the Power Press WIDE MODE Wide Zoom Normal Full Zoom Anamorphic Zoom Full1 (When the PC signal is input) Full2 (When the PC signal is input) Notes on selecting the wide screen mode Press one of the PICTURE MODE buttons (DYNAMIC, STANDARD, CINEMA and USER 1, USER 2 and USER 3) DYNAMIC STANDARD CINEMA Selecting to directly adjust the desired menu item Selecting desired adjust menu items in the order 1 Press RCP on the remote control 2 Press M/m to select “User1,” “User2” or “User3,” then press 3 Select the target color you want to adjust 4 Adjust the color of the specified portions 5 After the adjustment is complete, press Using the Menus 2 Press M/m to select a menu item, and press , or ,or 4 Make the setting or adjustment of an item When changing the adjustment level Items that cannot be adjusted To reset the picture that has been adjusted To reset the items that have been adjusted Page Page Page Page Page Page Page Page Page Page Page Page About the Preset Memory No Others Power Picture On-screendisplay Remote control Others Warning Indicators Message Lists Warning messages Caution messages Tools you need to get started: Standard Phillips screwdriver Cloth (for scratch protection) 1 Turn off the projector and unplug the AC power cord 6Close the lamp cover, then tighten the screws Remove the filter holder Remove the air filter 10 Attach the filter holder 11 Wipe dust off the Ventilation holes (intake) with a soft cloth 12 Place the project back on its original position 13 Turn on the projector, then select the desired setting item on the Setup menu. The menu screen below will be appeared Page System Input General Supplied accessories Optional accessories Preset Signals Page Preset memory numbers for each input signal Analog signal Digital signal Input Signals and Adjustable/Setting Items Screen menu When Using the PSS-H10Projector Suspension Support When using the 4:3 aspect ratio screen Attaching the PSS-H10projector suspension support Top view Front view Side view Tools you need to get started Phillips screwdriver: 110 mm (4 3/8 inches) or longer Flat-headscrewdriver: 110 mm (4 3/8 inches) or longer When using the 16:9 screen 5 Attach the ring (washer) by turning it clockwise