SpectraLink Corporation

Setup and Administration—NetLink e340/i640 Wireless Telephone

 

 

 

 

Mitel Networks ICP and 5220 IP Phone emulation

 

 

 

 

 

 

 

 

Message

 

Description

Action

 

 

No SVP IP

The Wireless Telephone is

Enter a valid NetLink SVP server

 

 

 

configured for “static IP” (as opposed

IP Address in the configuration

 

 

 

to “use DHCP”) and no valid NetLink

setting or change to “use DHCP.”

 

 

 

SVP Server address has been

 

 

 

 

entered.

 

 

 

No SVP Response

The NetLink SVP Server is not

This may be caused by bad radio

 

 

 

responding to requests from the

reception or a problem with the

 

 

 

Wireless Telephone.

NetLink SVP Server. The Wireless

 

 

 

 

 

Telephone will keep trying to fix the

 

 

 

 

 

problem for 20 seconds, and the

 

 

 

 

 

message may clear by itself. If it

 

 

 

 

 

does not, the Wireless Telephone

 

 

 

 

 

will restart. Report this problem to

 

 

 

 

 

the system administrator if it keeps

 

 

 

 

 

happening.

 

 

No SVP Server

Wireless Telephone can’t locate SVP

IP Address configuration of

 

 

 

Server.

NetLink SVP Server is wrong or

 

 

 

 

 

missing.

 

 

 

SVP Server is not working.

Check error status screen on

 

 

 

 

 

NetLink SVP Server.

 

 

 

No LAN connection at the SVP

Verify NetLink SVP Server

 

 

 

Server

connection to LAN.

 

 

 

 

 

 

 

No Net Access

Cannot authenticate / associate with

Verify the AP configuration.

 

 

 

AP

 

 

 

 

No Net Found

This indicates any of the following:

 

 

 

 

No radio link

Verify that the AP is turned on.

 

 

 

No ESSID – Autolearn not

Verify the ESSID of the wireless

 

 

 

 

supported (or)

LAN and enter or Autolearn it

 

 

 

 

incorrect ESSID

again if required.

 

 

 

 

 

 

 

 

 

Out of range

Try getting closer to an AP. Check

 

 

 

 

 

to see if other Wireless

 

 

 

 

 

Telephones are working within the

 

 

 

 

 

same range of an AP. If so, check

 

 

 

 

 

the ESSID of this Wireless

 

 

 

 

 

Telephone.

 

 

 

Incorrect WEP settings

Verify that all the WEP settings in

 

 

 

 

 

the Wireless Telephone match

 

 

 

 

 

those in the APs.

 

 

 

 

 

 

 

No Reg Domain

Regulatory Domain not set.

Configure the Regulatory Domain

 

 

 

 

 

of the Wireless Telephone

 

 

Not Installed!

A required software component is

Check that all required software

 

 

 

missing.

files are on the TFTP server, if

 

 

 

 

 

over-the-air downloading is being

 

 

 

 

 

used. If the error repeats, contact

 

 

 

 

 

SpectraLink Technical Support.

 

 

 

 

 

 

 

PN: 72-1084-02-B.doc

Page 39

Page 39
Image 39
SpectraLink 72-1084-02 manual Message Description Action