Stanley Black & Decker DS06 manual Hydraulic Hose Requirements, Hose Types, Hose Safety Tags

HYDRAULIC HOSE REQUIREMENTS

HOSE TYPES

Hydraulic hose types authorized for use with Stanley Hydraulic Tools are as follows:

➊Certifi ed non-conductive

➋Wire-braided (conductive)

➌Fabric-braided (not certifi ed or labeled non-conductive)

Hose ➊ listed above is the only hose authorized for use near electrical conductors.

Hoses ➋ and ➌ listed above are conductive and must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydrau- lic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

D O N O T R E M O V E T H I S T A G

D A N G E R				D A N G E R
1 FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE				3. DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR
WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAYRESULT IN DEATH				HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP
OR SERIOUS INJURY.				HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT
FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY				DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE
TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND				PERSONAL INJURY.
ELECTRIC LINES.				4. HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR
2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE ON				CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE
				HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.
OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FITTING
WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOSISTURE AND TEST				5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO
HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH SAFETY
				COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.
DEPARTMENT INSTRUCTIONS.				NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
				6. AFTER EACH USE STORE IN A CLEAN DRY AREA.
SIDE 1				SIDE 2
3	(shown smaller	than	actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

D A N G E R		D A N G E R
1 DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS	5.	CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO
NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR
ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.		COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.
2. FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY		NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND	6.	AFTER EACH USE STORE IN A CLEAN DRY AREA.
ELECTRIC LINES.

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

	SEE OTHER SIDE
SIDE 1	SIDE 2

(shown smaller than actual size)

HOSE PRESSURE RATING

D O N O T R E M O V E T H I S T A G

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hydraulic system.

9