Press F2 to enter Setup, PS/2 Mouse | SUPER MICRO Computer 6015B-Ni

Appendix A: BIOS POST Messages

Press <F1> to resume, <F2> to Setup, <F3> for previous

Displayed after any recoverable error message. Press <F1> to start the boot process or <F2> to enter Setup and change the settings. Press <F3> to display the previous screen (usually an initialization error of an Option ROM, i.e., an add-on card). Write down and follow the information shown on the screen.

Press <F2> to enter Setup

Optional message displayed during POST. Can be turned off in Setup.

PS/2 Mouse:

PS/2 mouse identiﬁ ed.

Run the I2O Conﬁguration Utility

One or more unclaimed block storage devices have the Conﬁ guration Request bit set in the LCT. Run an I2O Conﬁ guration Utility (e.g. the SAC utility).

System BIOS shadowed

System BIOS copied to shadow RAM.

UMB upper limit segment address: nnnn

Displays the address nnnn of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS which can be reclaimed by a virtual memory man- ager.

Video BIOS shadowed

Video BIOS successfully copied to shadow RAM.

A-5

Image 97

SUPER MICRO Computer 6015B-Ni manual Press F1 to resume, F2 to Setup, F3 for previous, Press F2 to enter Setup, PS/2 Mouse

Contents

Super Manual Revision Release Date June 20 About This Manual PrefaceManual Organization Advanced Serverboard Setup System SafetyAdvanced Chassis Setup Bios Preface Table of Contents Advanced Serverboard Setup System Safety Sgpio Advanced Chassis Setup Appendices BiosPage Overview Chapter Introduction Processors Serverboard FeaturesMemory Serial ATA ATI Graphics Controller Other Features System Power Server Chassis FeaturesControl Panel Backplane Headquarters Contacting Super MicroEurope Asia-Paciﬁc Superserver 6015B-Ni Manual Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Identifying the Sections of the Rack Rails Installing the System into a Rack Installing the Rack Rails Installing the Chassis Rails Installing the Server into a Rack Installing the Server into the Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the drive bays Checking the Drive Bay SetupSupplying power to the system Check the airﬂow Superserver 6015B-Ni Manual Control Panel Buttons Chapter System Interface Universal Information LED States Control Panel LEDsPage Superserver 6015B-Ni Manual Electrical Safety Precautions Chapter System Safety General Safety Precautions ESD Precautions Installing the Onboard Battery Operating Precautions Precautions Chapter Advanced Serverboard SetupHandling the Serverboard Unpacking Installing the Processor Processor and Heatsink InstallationPage Removing the Heatsink Installing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables Front Control Panel Header Pins JF1 Connecting the Control Panel Dimm Installation See Figure Installing MemoryI/O Ports Memory Support Installing Dimm into Slot Adding PCI Cards PCI card installationPCI Expansion Slots Super X7DBU Layout Serverboard Details Connector Description Jumper Description Default SettingX7DBU Quick Reference Other Description Connector Deﬁnitions Universal Information LED HDD LED Reset Button Power Fail LEDPower Button Universal Serial Bus USB0/1 Serial Ports Universal Serial Bus HeadersFan Headers Chassis Intrusion Power LED/SpeakerATX PS/2 Keyboard and PS/2 Mouse Ports Overheat LED Wake-On-Ring Wake-On-LAN JLAN1/2 Ethernet Ports Alarm Reset JAR VGA Enable/Disable Jumper SettingsExplanation Jumpers Cmos Clear Watch Dog Enable/Disable LAN Enable/DisableI2C Enable/Disable LAN1/LAN2 LEDs Onboard Indicators Floppy, IDE and Sata Drive Connections Floppy Connector Sata Ports IDE ConnectorPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Chassis Front and Rear Views Control Panel System Fans Installing a new fanSystem Fan Failure Replacing System Fans Accessing the Drive Bays Drive Bay Installation/Removal Drive bay conﬁguration Installing Components in the 3.5 Drive BaysMounting components in the drive bays Power Supply Failure Power SupplyRemoving/Replacing the Power Supply Removing the power supply Removing/Replacing the Power Supply Superserver 6015B-Ni Manual How To Change the Conﬁguration Data System BiosStarting the Setup Utility Chapter Main Bios Setup Running SetupPress the Delete key to enter Setup Bios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System Date Type IDE Channel 0 Master/Slave and Secondary IDE Master/Slave Transfer Mode LBA Mode ControlUltra DMA Mode Multi-Sector Transfers Sata Controller Mode Native Mode OperationSerial ATA Sata RAID Enable Parallel ATA Advanced Setup Power Loss Control Power Button BehaviorMemory Cache Cache System Bios Area Cache Video Bios Area Cache Base 512K-640K Default Primary Video AdapterCache Extended Memory Discrete Mtrr Allocation PCI Parity Error Forwarding Emulated IRQ SolutionsPCI Fast Delayed Transaction Reset Conﬁguration Data Latency Timer Enable MasterLarge Disk Access Mode Serr Signal Condition Crystal Beach Features High Temperature Dram OperationClock Spectrum Feature Branch 1 Rank Interleaving & Sparing USB Function Enabling Multi-Media TimerLegacy USB Support Advanced Processor Options Device Conﬁguration Intel Eist Support Available when supported by the CPUKBC Clock Input Serial Port a Serial Port B InterruptMode Floppy Disk Controller Event Log Validity DMI Event LoggingEvent Log Capacity View DMI Event Log COM Port Address Console RedirectionBaud Rate Console Type Hardware Monitor Logic CPU Temperature ThresholdVoltage Monitoring Fan Speed Control Modes Temperature Monitoring Available if supported by the CPU Clear System Event Logging System Event LoggingExisting Event Log Number Event Log Control Timer for Loading OS Minutes OS Boot Watch DogSystem Event Log/System Event Log List Mode Time Out Option Realtime Sensor Data User Password Is Supervisor Password IsSet Supervisor Password Set User Password Password on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Page Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settings Fail-Safe Timer NMI Failed System cache error Cache disabledAllocation Error for device Entering Setup Fixed Disk n PS/2 Mouse Boot Summary ScreenInvalid System Conﬁguration Data Device IRQ conﬂict Press F2 to enter Setup Press F1 to resume, F2 to Setup, F3 for previousSystem Bios shadowed Video Bios shadowedPage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Important Notes Appendix C Software InstallationSerial ATA Sata Introduction to Intel ESB2 Serial RAID RAID Conﬁgurations Conﬁguring Bios for Sata RAID Functions Native ModeIntel Matrix Storage Creating, Deleting and Resetting RAID Volumes Using the Intel ESB2 Sata RAID Utility Program Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Exiting the Intel Matrix Storage Manager Utility Resetting to Non-RAID and Resetting a RAID HDD New Operating System-Windows XP/2000/2003 Installation Installing Windows XP/2000/2003 for RAID Systems Installing the Operating System and other Software Programs Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Speciﬁcations Power Supply WeightSystem Cooling System Input Requirements