Connecting the Control Panel | SUPER MICRO Computer 6015B-Ni

SUPERSERVER 6015B-Ni User's Manual

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indi- cators. Please note that even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the other end of the cable to the Control Panel printed circuit board, located just behind the system status LEDs in the chassis.

See the Connector Deﬁ nitions section in this chapter for details and pin descrip- tions of JF1.

Figure 5-1. Front Control Panel Header Pins (JF1)

20	19
Ground	NMI
x (key)	x (key)
Power LED	Vcc
HDD LED	Vcc
NIC1	Vcc
NIC2	Vcc
OH/Fan Fail LED	Vcc
Power Fail LED	Vcc
Ground	Reset
Ground	Power
2	1

5-6

Image 40

SUPER MICRO Computer 6015B-Ni manual Connecting the Control Panel, Front Control Panel Header Pins JF1

Contents

Super Manual Revision Release Date June 20 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup Bios Preface Table of Contents System Safety Advanced Serverboard Setup Advanced Chassis Setup Sgpio Bios AppendicesPage Chapter Introduction Overview Serverboard Features ProcessorsMemory Serial ATA Other Features ATI Graphics Controller Server Chassis Features System PowerControl Panel Backplane Contacting Super Micro HeadquartersEurope Asia-Paciﬁc Superserver 6015B-Ni Manual Preparing for Setup Chapter Server InstallationUnpacking the System Rack Precautions Choosing a Setup LocationServer Precautions Rack Mounting Considerations Installing the System into a Rack Identifying the Sections of the Rack Rails Installing the Chassis Rails Installing the Rack Rails Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Checking the Drive Bay Setup Accessing the drive baysSupplying power to the system Check the airﬂow Superserver 6015B-Ni Manual Chapter System Interface Control Panel Buttons Control Panel LEDs Universal Information LED StatesPage Superserver 6015B-Ni Manual Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Unpacking Processor and Heatsink Installation Installing the ProcessorPage Installing the Heatsink Removing the Heatsink Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel Front Control Panel Header Pins JF1 Installing Memory Dimm Installation See FigureI/O Ports Memory Support Installing Dimm into Slot Adding PCI Cards PCI card installationPCI Expansion Slots Serverboard Details Super X7DBU Layout Jumper Description Default Setting Connector DescriptionX7DBU Quick Reference Other Description Connector Deﬁnitions HDD LED Universal Information LED Power Fail LED Reset ButtonPower Button Universal Serial Bus USB0/1 Serial Ports Universal Serial Bus HeadersFan Headers Power LED/Speaker Chassis IntrusionATX PS/2 Keyboard and PS/2 Mouse Ports Overheat LED Wake-On-LAN Wake-On-Ring Alarm Reset JAR JLAN1/2 Ethernet Ports Jumper Settings VGA Enable/DisableExplanation Jumpers Cmos Clear Watch Dog Enable/Disable LAN Enable/DisableI2C Enable/Disable Onboard Indicators LAN1/LAN2 LEDs Floppy Connector Floppy, IDE and Sata Drive Connections IDE Connector Sata PortsPage Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear Views Installing a new fan System FansSystem Fan Failure Replacing System Fans Drive Bay Installation/Removal Accessing the Drive Bays Drive bay conﬁguration Installing Components in the 3.5 Drive BaysMounting components in the drive bays Power Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supply Removing/Replacing the Power Supply Superserver 6015B-Ni Manual System Bios How To Change the Conﬁguration DataStarting the Setup Utility Chapter Main Bios Setup Running SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup Features Bios DateSystem Time System Date IDE Channel 0 Master/Slave and Secondary IDE Master/Slave Type LBA Mode Control Transfer ModeUltra DMA Mode Multi-Sector Transfers Native Mode Operation Sata Controller ModeSerial ATA Sata RAID Enable Parallel ATA Advanced Setup Power Button Behavior Power Loss ControlMemory Cache Cache System Bios Area Cache Video Bios Area Default Primary Video Adapter Cache Base 512K-640KCache Extended Memory Discrete Mtrr Allocation Emulated IRQ Solutions PCI Parity Error ForwardingPCI Fast Delayed Transaction Reset Conﬁguration Data Enable Master Latency TimerLarge Disk Access Mode Serr Signal Condition High Temperature Dram Operation Crystal Beach FeaturesClock Spectrum Feature Branch 1 Rank Interleaving & Sparing Enabling Multi-Media Timer USB FunctionLegacy USB Support Advanced Processor Options Intel Eist Support Available when supported by the CPU Device ConﬁgurationKBC Clock Input Serial Port a Interrupt Serial Port BMode Floppy Disk Controller DMI Event Logging Event Log ValidityEvent Log Capacity View DMI Event Log Console Redirection COM Port AddressBaud Rate Console Type CPU Temperature Threshold Hardware Monitor LogicVoltage Monitoring Fan Speed Control Modes Temperature Monitoring Available if supported by the CPU System Event Logging Clear System Event LoggingExisting Event Log Number Event Log Control OS Boot Watch Dog Timer for Loading OS MinutesSystem Event Log/System Event Log List Mode Time Out Option Realtime Sensor Data Supervisor Password Is User Password IsSet Supervisor Password Set User Password Password on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Page Appendix a Bios Post Messages System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settings System cache error Cache disabled Fail-Safe Timer NMI FailedAllocation Error for device Entering Setup PS/2 Mouse Boot Summary Screen Fixed Disk nInvalid System Conﬁguration Data Device IRQ conﬂict Press F1 to resume, F2 to Setup, F3 for previous Press F2 to enter SetupSystem Bios shadowed Video Bios shadowedPage Appendix B Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Appendix C Software Installation Important NotesSerial ATA Sata Introduction to Intel ESB2 Serial RAID RAID Conﬁgurations Conﬁguring Bios for Sata RAID Functions Native ModeIntel Matrix Storage Using the Intel ESB2 Sata RAID Utility Program Creating, Deleting and Resetting RAID Volumes Creating a RAID 0 Volume Creating a RAID 1 Volume Creating a RAID 10 RAID 1+ RAID Creating a RAID 5 Set Parity Deleting a RAID Volume Resetting to Non-RAID and Resetting a RAID HDD Exiting the Intel Matrix Storage Manager Utility Installing Windows XP/2000/2003 for RAID Systems New Operating System-Windows XP/2000/2003 Installation Installing the Operating System and other Software Programs Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page Appendix D System Speciﬁcations Weight Power SupplySystem Cooling System Input Requirements