Reference Guide: TT128x High Definition Professional Receiver/Decoder Page 3-1
ST.RE.E10141.5
Chapter 3

3. Operating the Equipment Locally

Contents
3.1 Powering the Equipment...........................................3-3
3.1.1 Switching On................................................ 3-3
3.1.2 Power-up Operating Modes..........................3-3
3.2 Front Panel Controls and Pushbuttons..................... 3-4
3.3 Front Panel Operating Modes...................................3-4
3.3.1 General.........................................................3-4
3.3.2 Navigate Mode............................................. 3-4
3.3.3 Edit Mode..................................................... 3-4
3.4 Using the Local Controls........................................... 3-6
3.4.1 LCD Menu Descriptions................................3-6
3.4.2 Selecting a Menu Option.............................. 3-6
3.4.3 Entering a Menu Value................................. 3-6
3.5 Setting Up Preset Services (Menu 1)........................3-7
3.5.1 Using Preset Services.................................. 3-7
3.5.2 Setting Up a Preset Service......................... 3-7
3.6 Setting Up the Input (Menu 2)...................................3-7
3.6.1 QPSK Satellite Receiver...............................3-7
3.6.2 HOM Satellite Receivers
(TT1280/HWO/HOM)....................................3-8
3.6.3 DVB-S2 Satellite Receiver
(TT1280/HWO/DVBS2 and
TT1280/HWO/DVBS2/IF/CONST)................3-9
DVB-S2 Input Option Card
TT1280/HWO/DVBS2/IF/CONST.................3-9
3.6.4 Telco Receiver - TTV G.703.......................3-10
3.6.5 10/100BaseT IP..........................................3-10
3.7 Service Configuration (Menu 3).............................. 3-11
3.7.1 Selecting and Setting Up a Service............ 3-11
3.7.2 Selecting the Video Component................. 3-11
3.7.3 Selecting the Audio Component................. 3-12
Introduction.................................................3-12
Selecting the Audio Manually......................3-12
3.7.4 Setting Up Asynchronous Data (RS-232)...3-13
3.7.5 Setting Up High-speed Data over
Ethernet...................................................... 3-13
3.7.6 Setting Up High-speed Synchronous
Data (RS-422).............................................3-13
3.7.7 Setting Up Closed Captions........................3-14
3.7.8 Setting Up VITC..........................................3-14
3.7.9 Setting the PCR PID Menu.........................3-14
3.7.10 Viewing the Network ID Menu.....................3-14
3.8 Setting Up the Conditional Access/Scrambling
(Menu 4)..................................................................3-14
3.8.1 Introduction.................................................3-14
3.8.2 Basic Interoperable Scrambling System
(BISS) (Menu 4.4).......................................3-15
3.8.3 Remote Authorisation System (RAS)
(Menu 4.1)...................................................3-15
3.8.4 TANDBERG Director (Menu 4.3)................3-15
3.8.5 DVB Common Interface (Menu 4.3)............3-15
3.9 Setting Up the Transport Stream Output (Menu 5). 3-16
3.9.1 Set-up Procedure........................................3-16
3.9.2 Setting the Output Connector..................... 3-16
3.9.3 Transport Stream Output Bit-rates..............3-16
3.9.4 Transport Stream Packet Lengths..............3-17
3.9.5 ASI Output Mode........................................ 3-17
3.10 Setting Up the Alarms (Menu 6)..............................3-17
3.11 Setting Up System Parameters (Menu 7)................3-18
3.12 Restarting the Unit...................................................3-19
List of Figures
Figure 3.1: Power-up Operating Mode.......................................... 3-3
Figure 3.2: Front Panel Controls and Pushbuttons....................... 3-4