Manuals / Thermal Comfort / Power Tools / Welder

Thermal Comfort 3000 manual Access Panel Parts Replacement, Front Panel/Chassis Parts Replacement

Models: 3000

1 86
Download 86 pages 31.64 Kb
Page 39
Image 39

2.Loosen the two screws of the Work Cable strain relief securing the Work Cable at the Front Panel.

3.Remove the nut (under the Horizontal Chassis Panel) securing the Work Cable connection to the Shunt Assembly.

4.Pull the Work Cable from the unit.

5.Install the replacement Work Cable by reversing the above procedure.

5.05Access Panel Parts Replacement

NOTE

Refer to Section 6.04, Access Panel Replacement Parts, for parts list and overall detail drawing.

A.CURRENT Knob Replacement

1.Turn the CURRENT adjustment fully counter clock- wise and note the location of the pointer on the knob.

2.Loosen the screw securing the Current Knob to the potentiometer shaft.

3.Remove the old knob.

4.Place the replacement Current Knob on to the po- tentiometer shaft with the location of the pointer the same as noted in step 1.

5.Tighten the screw to secure the knob to the poten- tiometer shaft.

B.ON/OFF Switch Replacement

1.Unlatch the Access Panel to gain access to the rear of the ON/OFF Switch.

2.Disconnect all the wiring to the ON/OFF Switch.

3.Squeeze the top and bottom of the switch while pulling it out of the Access Panel

4.Install the replacement ON/OFF Switch by revers- ing the above procedure.

C.RUN/SET/PURGE Switch Replacement

1.Unlatch the Access Panel to gain access to the rear of the RUN/SET/PURGE Switch.

2.Disconnect all the wiring to the RUN/SET/PURGE Switch.

3.Squeeze the top and bottom of the switch while pulling it out of the Access Panel

4.Install the replacement RUN/SET/PURGE Switch by reversing the above procedure.

D.LED/Current Control PC Board Assembly Replacement

1.Remove the Current Knob per paragraph 'A' above.

2.Unlatch the Access Panel to gain access to the LED/ Current Control PC Board.

3.Remove the four screws and washers securing the LED/Current Control PC Board to the Access Panel.

4.Disconnect the connector at J5 of the LED/Current Control PC Board.

5.Install the replacement LED/Current Control PC Board by reversing the above procedure.

E.Access Panel Replacement

1.Remove the Right Side Panel per Section 5.04-B.

2.Remove the following components from the Ac- cess Panel:

•Current Knob per paragraph 'A' above.

•ON/OFF Switch per paragraph 'B' above.

•RUN/SET/PURGE Switch per paragraph 'C' above.

•LED/Current Control PC Board per paragraph 'D' above.

3.Remove the four screws securing the Access Panel to the LED/Current Control PC Board standoffs.

4.Install the replacement Access Panel by reversing the above procedure.

5.06Front Panel/Chassis Parts Replacement

NOTE

Refer to Section 6.05, Front Panel/Chassis Replace- ment Parts, for parts list and overall detail draw- ing.

A. Internal Coolant Filter Replacement

The Internal Coolant Filter Assembly is located inside behind the Left Side Panel (viewed from the front of the unit). The filter is attached to the Radiator inside of the Lower Front Panel.

1.Remove the Left Side Panel from the Power Sup- ply per Section 5.04-B.

2.Locate the Internal Coolant Filter near the front of the unit.

Manual 0-2533

35

REPLACEMENT PROCEDURES

Page 38 Page 40
Page 39
Image 39
Thermal Comfort 3000 manual Access Panel Parts Replacement, Front Panel/Chassis Parts Replacement
Page 38 Page 40

3000 specifications

Thermal Comfort 3000 is an innovative solution designed to enhance indoor climate by ensuring optimal thermal comfort for users. As the demand for energy efficiency and sustainable building practices grows, Thermal Comfort 3000 emerges as a key player in providing customizable and effective climate control systems.

One of the main features of Thermal Comfort 3000 is its advanced smart technology that allows for precise temperature regulation based on real-time data. It utilizes sensors that monitor indoor and outdoor temperatures, humidity levels, and even occupancy patterns. This data is then analyzed to optimize the heating and cooling systems, ensuring that energy is used efficiently. With its ability to automatically adjust to changing conditions, users can enjoy a consistent and comfortable environment without excessive energy consumption.

Thermal Comfort 3000 is built with user convenience in mind. It comes equipped with a user-friendly interface that enables easy adjustments and programming. Through a dedicated mobile app, users can control their indoor climate remotely, providing flexibility for those with busy lifestyles. Furthermore, the system offers customizable settings that cater to individual preferences, ensuring that everyone in a space can enjoy their ideal thermal environment.

The technology behind Thermal Comfort 3000 incorporates sustainable practices, utilizing eco-friendly refrigerants and energy-efficient components. This not only reduces the carbon footprint of buildings but also lowers energy costs for users. The system can be integrated with renewable energy sources, such as solar panels, creating a truly sustainable heating and cooling solution.

Thermal Comfort 3000 also features advanced filtration systems that improve indoor air quality. By removing allergens, dust, and other pollutants from the air, it promotes a healthier living environment. This is especially beneficial for individuals with allergies or respiratory issues, making Thermal Comfort 3000 an excellent choice for homes and commercial spaces alike.

In summary, Thermal Comfort 3000 represents the future of climate control technology. Its combination of smart features, user-centric design, and sustainability makes it an ideal solution for enhancing thermal comfort in any indoor environment. With its innovative approach, it not only ensures comfort but also promotes energy efficiency and environmental responsibility, making it a worthwhile investment for modern living.