Manuals
/
Thermo Products
/
Household Appliance
/
Furnace
Thermo Products
CHX1-100N, CDX1-75N, CHX1-125N, CHX1-75N, CDX1-125N, CDX1-100N operation manual Figure
Models:
CDX1-100N
CDX1-125N
CHX1-100N
CHX1-75N
CHX1-125N
CDX1-75N
1
21
59
59
Download
59 pages
47.89 Kb
18
19
20
21
22
23
24
25
<
>
Troubleshooting
Specification
Install
Parts list
Appendix - B Wiring Diagrams
Connecting The Exhaust Vent To The Inducer
Diagnostic Features
I. Condensate Drain Line And Trap Assembly
Go to Checkout Procedure below
Measuring And Adjusting Heat Input Rate
Page 21
Image 21
All installations and services must be performed by qualified service personnel.
Figure 7
15
Page 20
Page 22
Page 21
Image 21
Page 20
Page 22
Contents
OR LP GAS PROPANE CDX1-75N CDX1-100N CDX1-125N
MODELS
INSTALLATION AND OPERATION MANUAL
TWO STAGE CONDENSING GAS FURNACE
I. SAFETY INFORMATION
This and the previous page contain reproductions of the various warning and instruction labels placed on the Thermo Pride Two Stage Condensing Gas Furnaces. Please read and comply with the contents of these labels
1.A windows be opened
Page
INDEX
SECTION
BEGINNING PAGE
II. FURNACE SPECIFICATIONS CHX1 SERIES
CDX1 SERIES
INSTALLATION PARTS PACKAGES - CHX1-75
PARTS PACKAGE
INSTALLATION PARTS PACKAGES – CDX1-75
DESCRIPTION
PART #
PARTS PACKAGE
INSTALLATION PARTS PACKAGES – CDX1-100-125
DESCRIPTION
PART #
III. GENERAL INSTALLATION
B1. CDX1 HORIZONTAL APPLICATION
B. FURNACE LOCATION
Figure
MAXIMUM VENT LENGTH TABLE
D. GENERAL REQUIREMENTS FOR VENTING CHX1/CDX1
Figure
E. SIDEWALL VENTING
Figure 3. VENT TERMINAL LOCATION REQUIREMENTS
E1. SINGLE PIPE SIDEWALL VENTING OPTION
VENT TERMINAL LOCATION GUIDELINES
Optional Terminations
Figure
Figure
Figure
2. CONNECTING THE EXHAUST VENT TO THE INDUCER
Figure Figure Figure
Figure
Figure
I. CONDENSATE DRAIN LINE AND TRAP ASSEMBLY
Figure 14. TRAP ASSEMBLY MOUNTED ON CHX1
Figure 15. TRAP ASSEMBLY MOUNTED ON CDX1
2.Determine on which side of furnace the condensate disposal line is to be run NOTICE: On CHX1/CDX1’s this must be the same side as the flue outlet or bottom of unit. Attach the condensate trap to the furnace casing using the #8x3/4” sheet metal screws provided in the parts package. Pilot holes are provided on both sides of the casing for mounting
J. GENERAL GAS PIPING
K. FILTERS 1. CHX1 MODELS: HIGHBOYS
Figure
Figure
2. CDX1 MODELS: COUNTERFLOWS
Figure
3. USE OF NON-THERMOPRIDE FILTER RETENTION MEANS
3. THERMOSTAT CONNECTIONS AND ANTICIPATOR SETTING
4.BLOWER AND CONTROL PANEL WIRING Figure
2-StageBlower Settings from factory Table
IV. STARTING THE UNIT A. SEQUENCE OF OPERATIONS
FLAME MUST BE DETECTED
IF SYSTEM IS IN LOCKOUT
OPERATING INSTRUCTIONS
B. INITIAL START UP
Observe the following precautions when measuring
Measuring And Adjusting Heat Input Rate
A.Burner manifold pressure with a pressure gauge
B.Gas flowrate by clocking gas meter
NOTICE: A U-tubemanometer, measuring pressure in inches of water column, is recommended for all gas pressure measurements. However, an aneroid pressure gauge, in good working condition, capable of reading pressure changes of 0.05 in. W.G., or less, that was recently calibrated within the last year, is a satisfactory alternate. These two 2 devices will be considered as equivalent and interchangeable. Either device is referred to below as a “pressure gauge”
Fuel gas higher heating value ç in
Heat input rate in BTUH =
Fuel gas flowrate in CFH
Fuel gas flowrate in CFH =
Operating Mode, and Type of Fuel
21.Go to Checkout Procedure below
Checkout Procedure
TABLE 6 - CONVERTING GAS FLOW RATE
V. INSTALLERS INSTRUCTIONS TO USER
C. FURNACE CHECKOUT PROCEDURE
Figure VI. TROUBLESHOOTING
Power must be disconnected before servicing
DIAGNOSTIC FEATURES
TROUBLESHOOTING GUIDE
IS INDUCER RUNNING ON LOW SPEED? YES DOES THE HOT
DO BURNERS STAY LIT PAST PROOF OF FLAME CHECK?
REPLACE THE 50V61-143CONTROL
WHEN THERMOSTAT IS
Appendix –AReplacement Parts List
Page
Page
Page
Appendix - B Wiring Diagrams
