Manuals / Thermo Products / Household Appliance / Furnace

Thermo Products PHCFA072DV4R operation manual Oil Fired Furnace

Models: PHCFA072DV4R

1 55

Download 55 pages 42.07 Kb

Page 1

OIL FIRED FURNACE

OIL FIRED FURNACE

INSTALLATION AND OPERATION MANUAL

WITH USERS INFORMATION SECTION

MODEL:

OHCFA072DV4R

WARNING: IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THIS MANUAL. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER, OR SERVICE AGENCY.

PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION, INITIAL FIRING, AND BEFORE PERFORMING ANY SERVICE OR MAINTENANCE. THESE INSTRUCTIONS MUST BE LEFT WITH THE USER AND SHOULD BE RETAINED FOR FUTURE REFERENCE BY QUALIFIED SERVICE PERSONNEL.

THERMO PRODUCTS, LLC.

PO BOX 217

NORTH JUDSON, IN 46366

PHONE: (574) 896-2133

MO-490
ECN 5095-PC 131030	Made IN USA

Image 1

Thermo Products PHCFA072DV4R operation manual Oil Fired Furnace, With Users Information Section Model

Contents

WITH USERS INFORMATION SECTION MODEL OIL FIRED FURNACECONTENTS Model Number Digit ConfigurationFuel Heat Exchanger IdentifierI. SAFETY SECTION Page A. CODES AND CLEARANCES b.Non-combustiblematerial a. Combustible materialTYPE OF FROMII. GENERAL INSTRUCTIONS A. VENTING Fig-1 Fig-2 B.INSTALLATION OF VENTORFig-3 A. The exit termination of the draft system shall not be less than 7’ above grade when located adjacent to public walkways Fig-4 C. Condensate Drain Line ConnectionsD. DUCT WORK/AIR CONDITIONING Fig-5 Furnace with coil cabinet E. Air Filter Mounted External to FurnaceModel Number MaximumFilter Type Air VelocityH. BURNER SPECIFICATIONS AND APPLICATIONS G. BURNER INSTALLATIONF. LIMIT POSITION AND LOCATION Fig-7NOZZLE SIZE OIL NOZZLE CAPACITY CHARTEQUIVALENT HEAT EFFECTIVE HEATINGPage Electrical Connections J. ELECTRICAL WIRINGRoom Thermostat Post-PurgeTimer L. Blower Motor Speed Selection Thermostat Anticipator SettingLow= Red Med Low= Purple Med= Blue Med Hi= Yellow OHCFA072DV4High= Black M.BLOWER CONTROLLER INFORMATION FOR ECM MOTOR TERMINAL DEFINITIONS & FIELD WIRINGInputs Outputs Operating Modes Motor Blower Speed N.STARTUP PROCEDURES TROUBLE SHOOTINGFor Your Safety Read Before Operating DIAGNOSTIC FEATURES2. Adjustment of Burner Combustion i.STOP! Read the safety information aboveOperating Instructions To Turn Off Oil to Applianceb.Set the room thermostat above room temperature NOTICE Minimum return air temperature is 550 F 4.Setting Supply Air Temperature Rise 3. Adjustment Of Heat Input Rate5. Checkout Procedure B. INSPECTION AREAS D. FILTER CLEANING AND LOCATIONCAUTION DO NOT ATTEMPT TO MAKE REPAIRS YOURSELF CAUTION DO NOT ATTEMPT TO START THE BURNER WHENIV. INSTALLERS INSTRUCTIONS TO USER SAFETY DURING SERVICING AND INSPECTION V.DEALER MAINTENANCEA.GENERAL INSPECTION B.HEAT EXCHANGER CLEANING INSTRUCTIONS Fig-11 Fig-12 Fig-13 D. ELECTRICAL SYSTEM Filter maintenance procedureE. SUPPLY/RETURN AIR BLOWER F. SUPPLY/RETURN AIR FILTERDo not attempt to start burner when ON STARTUP 2.Remove the furnace front door Fig-16 PERSONNEL, AND NOT BY THE FURNACE OWNER VII. TROUBLESHOOTINGPage Page Page Page Page CUSTOMER OIL FIRED CENTRAL FURNACESHEATING SYSTEM COMBUSTIONAppendix - A Replacement Parts DESCRIPTION 3ELECTRODE ASSEMBLY 4PUMP 5MOTOR 6BLOWER WHEEL1AIR TUBE COMPLETE 2BLAST TUBE ONLY 7PRIMARY CONTROL 8PHOTO CELL 9INSULATING AMULETPage OHCFA072DV4R Appendix - B Wiring Diagram