ASSEMBLY

GENERAL

The Rhino 1348, 1548, and 1948 differ slightly in some areas. Notes have been provided for these differ- ences, be sure to refer to the proper note for your machine.

TRACTOR REQUIREMENTS

Before preparing the tractor for the machine make sure that specifications of the tractor meet the re- quirements listed below.

A.6 spline P.T.O. of 1-3/8" dia.

B.A P.T.O. output of 540 rev/min.

C.A top link is available.

D.As a guide for suitable tractor size the ballasted weight of tractor should exceed 2750 kg (6050 lbs)

E.Adequate ballast should be added to the rear wheel opposite to the arms and front of the tractor to ensure stability. The amount will vary depending on type of tractor used and prevailing conditions.

MACHINE PREPARATION

The machine will normally be delivered with the arms fully assembled to the mainframe, but with the mower head detached.

The lifting points FIGURE 3-1 (A), 3-1 (B) and FIGURE 3-2 (A) are for machines without the mower head attached or hydraulic oil. When lifting machine in anything other than this conditions extreme care should be exercised as the center of gravity may change. Only personnel experienced in lift and hoist operation should attempt it. Note the Lifting Point and transport straps / retaining chain differ between the 1348/ 1548 and the 1948 (see FIGURE 3-1).

A.Position the machine on a flat hard surface.

B.If not already fitted, lift the machine and fit the parking stands which will be found stored under the mainframe.

C.Remove the transport straps 3-1 (C), 3-1 (D), identified by the red panel.

Remove the retaining chain and greasing setscrew from transport plate and fit into tapped hole of first/

second arm pin and tighten up.

NOTE: The second arm on the RBF-12 is required to be moved from on top the first arm to below the first arm and the second ram re-fitted to it.

FIGURE 3-1

RBF-19C 07-04

Assembly Section 3-2

© 2004 Alamo Group Inc.

 

Page 35 Page 37
Page 36
Image 36
Tiger RBF-19C manual General, Tractor Requirements, Machine Preparation
Page 35 Page 37

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents