ASSEMBLY

INITIAL RUN

A.Check that the motor hoses are connected together.

B.Run tractor engine at idle speed and engage PTO drive.

C.Increase PTO speed gradually up to 360 rev/min.

D.The pump will start operating during run-up. Flexing of the motor hoses and turbulence of the oil tank can be observed.

E.When pump is operating run system at 360 rev/min PTO speed for 10 minutes.

F.Check oil level. The oil level is correct when visible in the bottom of the filler assembly strainer.

BLEEDING RAMS

The ram cylinders at first will be full of air, therefore it may take some time for the cylinders to move after the control levers have been operated. Ensure sufficient space is available to allow for any unexpected movement of the arms.

Bleeding the First Ram

Due to the fact that the first arm can move past the vertical (overcenter) when fully raised, a restrictor may be fitted in the first ram hydraulic system to give a slow, controlled movement of the arm past center. It is essential that the first ram is fully bled to prevent fall back to the arm when the arms are stretched out and taken past vertical.

NOTE: The following instructions must be carried out before any attempt is made to raise more than one arm at a time.

A.Engage PTO drive with tractor engine at idle speed.

B.Increase PTO speed to 360-400 rev/min.

C.Fully retract second cylinder.

D.Fully retract the first cylinder.

E.Slacken hose connection at the bottom of the first cylinder.

G.Continue the bleeding until only clean, bubble-free oil is escaping from the fitting. Tighten fitting.

H.Open and close all cylinders to expel the air.

I.Check the oil level in the tank/tractor hydraulic oil reservoir and top up if necessary.

J.Check all hydraulic connections in the cylinder circuit for tightness.

WARNING! Do not raise more than one arm at a time until cylinders are completely free of air. Unex- pected movement of the arms can be dangerous.

RBF-19C 07-04

Assembly Section 3-14

© 2004 Alamo Group Inc.

 

Page 47 Page 49
Page 48
Image 48
Tiger RBF-19C manual Initial RUN, Bleeding Rams, Bleeding the First Ram
Page 47 Page 49

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.
Top Page Image Contents