ASSEMBLY

B.Prepare the mower by using the top link to join the mower's upper hitch point to the A frame upper clevis.

C.Using the lower hitch pins, fix the A frame tube ends in the inner clevis of each lower hitch point. At this stage the lower hitch pins should not protrude into the outer lower hitch clevis.

D.Carefully reverse the tractor so that the ball joint on the tractor linkage line up with the clevis on the mainframe. Connect the mower with hitch pins that are retaining the A frame. By this time the hitch pin should pass through both A frame tubes and lift arm ball ends.

E.Connect the upper hitch point of the A frame to the tractor upper hitch point, adjusting the top link as necessary.

F.Lift machine to its working height, ensuring that the machine is level by adjusting the tractor linkage to suit.

G.Fit the top strut and the top link bracket, connecting the struts together with the two bolts provided. It may be necessary on certain tractors to twist the struts to fit.O

H.The A frame is now a rigid unit and the tractor lift arms can be lowered by removing the weight from the tractor hydraulics.

NOTE: It is important that at this stage the tractor lower link check chains are fully tightened to remove all horizontal motion from the tractor lower links.

I.Remove front and rear stands from the mainframe and store underneath the mainframe. (See Gen- eral Arrangement.)

J.Adjust the top link until the machine is square with the tractor.

FITTING PTO

NOTE: The tank must be filled with the correct grade of oil before the PTO is fitted. See Maintenance

Section.

Due to many different makes and sizes of tractor to which Servis mowers can be fitted, a nominal length of PTO shaft is supplied with the machine. In some cases it may be found that this PTO shaft is too long and will have to be shortened.

NOTE: Minimum engagement of PTO square drive is 100mm (4 in) and 150mm (6 in) for the Lemon Tube Type in the working position. This measurement must be taken into account when shortening the PTO shaft.

Before fitting PTO shaft to tractor grease the sliding drive shafts and bearing units.

Fit PTO to tractor ensuring locking pin on the splined coupling is fully engaged.

RBF - 19C 07-04

Assembly Section 3-5

© 2004 Alamo Group Inc.

 

Page 39
Image 39
Tiger RBF-19C manual Fitting PTO, Section

RBF-19C specifications

The Tiger RBF-19C is a remarkable example of advanced unmanned aerial technology, designed primarily for reconnaissance and battlefield surveillance. This drone has garnered attention for its exceptional capabilities and cutting-edge features that make it a valuable asset for military and defense operations.

One of the standout characteristics of the RBF-19C is its high-altitude endurance. The drone is engineered to operate at significant elevations, which allows it to cover vast terrains while remaining undetected. With a maximum altitude capability of 20,000 feet, it can conduct prolonged missions, gathering intelligence over hostile areas without risking human pilots.

Under the hood, the Tiger RBF-19C incorporates advanced sensor technologies that enable it to deliver real-time data. Equipped with high-definition cameras, multispectral sensors, and infrared technology, it can capture detailed images and videos even in adverse weather conditions and low-light environments. This capability significantly enhances situational awareness for ground forces, making decision-making faster and more efficient.

Another notable feature of the RBF-19C is its extended operational range. The drone can maintain a communication link over distances exceeding 200 kilometers, enabling it to operate far beyond the frontline. This extended range allows for strategic reconnaissance missions, providing vital intelligence without exposing personnel to danger.

In terms of maneuverability, the Tiger RBF-19C is designed for versatility. It features a robust flight control system that allows for nimble navigation in complex environments. The drone can perform various flight patterns, including loitering and waypoint navigation, which is particularly useful for surveillance missions where constant observation of a target is crucial.

Moreover, the RBF-19C is built with a modular design, allowing for quick modifications and upgrades to suit different mission requirements. This adaptability ensures that it can be easily retrofitted with new technology or payloads, keeping it relevant amidst rapidly evolving warfare tactics.

Lastly, the RBF-19C is renowned for its stealth capabilities. Designed with a low radar cross-section and noise-reduction technologies, it minimizes its visibility to enemy radar systems, enabling covert operations. This attribute is essential for missions that require undetected data gathering.

In conclusion, the Tiger RBF-19C represents a significant advancement in drone technology, combining endurance, advanced sensors, extended range, and stealth. Its sophisticated design and operational capabilities make it an invaluable tool for modern military forces, enhancing their ability to carry out reconnaissance and maintain situational awareness on the battlefield.