Manuals / Brands / TV and Video / CRT Television / Toshiba / TV and Video / CRT Television

Toshiba 32A41 Point the remote control at the VCR or cable TV converter

1 35

Download 35 pages, 1.55 Mb

Set up

Preparation

Using the remote control with a VCR or cable TV converter

•To use your TV remote control to operate a VCR, set the TV/CABLE/VCR switch to VCR. The shaded buttons shown in the picture below will then operate the VCR; the unshaded buttons will operate the TV as usual.

•To use your TV remote control to operate a cable TV converter, set the TV/CABLE/VCR switch to CABLE. The shaded buttons shown in the picture below will then operate the converter; the unshaded buttons will operate the TV as usual.

•If you have a non-Toshiba VCR or cable TV converter, you must first program the remote control to recognize your VCR or converter brand (see pages 11–13 for details).

Point the remote control at the VCR or cable TV converter

Basic Operation

RECALL MUTE

o

POWER

POWER

Reference Section Advanced Operation

Channel Numbers

Press to directly access channels (as opposed to the Channel s/t buttons).

TV/CABLE/VCR Switch

Set to CABLE to control the cable converter; set to VCR to control the VCR.

TV/VCR

Press to select TV mode to view one program while recording another program.

REC

Starts tape recording.

SLOW

In play mode, press to view a slow-motion picture.

PAUSE

In play or record mode, press to freeze the picture; press again to release.

1 2 3

4 5 6

7 8 9

CH RTN

100 0 ENT

CH

VOL MENU/ VOL

ENTER

CH

TV

CABLE

VCR EXIT

FAV CH TV/VIDEO

A

REC TV/VCR STOP PLAY

STILL SOURCE PIP

SLOW PAUSE REW FF

PIP CH LOCATE SWAP

Turns the VCR (or cable TV converter) on and off.

ENTER

Required by some VCRs and cable TV converters to change the channel.

CHANNEL s/t

s selects the next higher channel; t selects the next lower channel.

STOP

Stops the tape.

PLAY

Begins tape playback.

FF

Fast-forwards the tape.

In play mode, press to view the picture moving rapidly forward.

REW

Rewinds the tape.

In play mode, press to view the picture moving rapidly backward.

10

Contents

up Set Preparation Operation Basic Operation Advanced Section Reference CAUTION ATTENTION Note to CATV system installers in the USA Precautions Introduction Connecting your TV Preparing the remote control for use Location of controls on TV and remote control Using the remote control with a VCR or Set up Reference Section Advanced Operation Basic Operation Exploring your new TV 36A41 32A41 Audio and video cables are usually NOTE REGARDING PICTURE QUALITY When connecting video equipment, such as a VCR or DVD player: –For GOOD picture quality: Use regular video cables For BETTER picture quality: If your equipment has (continued) Connecting a cable converter box and a VCR Connecting a satellite receiver and a VCR Connecting a DVD player with component video and a VCR Connecting two VCRs •two pairs of audio cables (two single audio cables for mono VCRs) Section Installing the remote control batteries 1 Slide the battery cover off the back of the remote control 3 Slide the battery cover back onto the remote control until the lock snaps For details on the use of each control, refer to pages in brackets TV front panel Model 32A41 Model 36A41 Remote control Point the remote control at the VCR or cable TV converter Channel Number –If the correct code was entered, the VCR or converter will turn off If the correct code was entered –If the VCR or converter does not respond, repeat steps 1–4using another code If the VCR or converter does not respond to a different code VCR code table Cable TV converter code table Page Turning the TV set on Selecting the on-screendisplay language Understanding the Auto Power Off feature Understanding the Last Mode Memory feature TV/CABLE function CH PROGRAM function ADD/ERASE function 4 To add the channel: To erase the channel: Operation Basic Operation Selecting a TV channel Select a channel in one of the following two ways: ●Scan through the programmed channels in numerical sequence: –Press CHANNEL s to select the next higher channel RTN Adjusting the picture quality Pressing Selection To reset the Picture and Sound adjustments to the factory settings Selecting the color temperature The color temperature modes change the color tones of the picture 1 Press MENU until the Picture 2 menu is displayed on-screen 2 Press t or s until COLOR TEMPERATURE is displayed in purple 3 Press T or S until the desired mode is displayed in purple You can adjust the sound quality (BASS, TREBLE and BALANCE) to suit your taste Adjusting the sound quality 1 Press MENU until the Audio menu is POWERdisplayed on-screen 2 Press s or t until the item you want to Setting the off-timer Canceling the off-timer Stereo Sound: SAP: Surround Sound: Listening to stereo sound Activating the surround sound effect Listening to a second audio program (SAP) To deactivate the SAP feature: Programming your favorite channels Selecting your favorite channels Viewing captions or text Opening the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu (continued) Unblocking programs temporarily BLOCK CHANNEL function Page Page For additional information, visit our web site: ATTENTION CANADIAN CONSUMERS: TOSHIBA AMERICA CONSUMER PRODUCTS, INC PRINTED IN USA