Toshiba 32A41 32

Set up

Preparation

Reference Section Advanced Operation Basic Operation

Specifications

Television system	NTSC standard
Channel coverage	VHF: 2 through 13
	UHF: 14 through 69
	Cable TV: mid band (A-8 through A-1, A through I)
		super band (J through W)
		hyper band (AA through ZZ, AAA, BBB)
		ultra band (65 through 94, 100 through 125)
Power source	120V AC, 60Hz
Power consumption	32A41: 96W (average)
	36A41: 92W (average)
Audio power	5W + 5W
Speaker type	2-3/8 x 4-3/4 inches (60 x 120 mm)
Audio/Video terminals	S-VIDEO INPUT
	Y-INPUT: 1V (p-p), 75 ohm, negative sync.
	C-INPUT: 0.286V (p-p) (burst signal), 75 ohm
	AUDIO/VIDEO INPUT
	VIDEO: 1V(p-p), 75 ohm, negative sync.
	AUDIO: 150mV(rms) (30% modulation equivalent, 47k ohm)
	ColorStream™ (component video) INPUT
	Y: 1V (p-p), 75 ohm
	CR (PR): 0.7 V (p-p), 75 ohm
	CB (PB): 0.7 V (p-p), 75 ohm
	AUDIO/VIDEO OUTPUT
	VIDEO: 1V(p-p), 75 ohm, negative sync.
	AUDIO: 150mV(rms) (30% modulation equivalent, 4.7k ohm)
Dimensions	32A41:	Width	30-5/8 inches (778mm)
		Height	27-5/16 inches (693mm)
		Depth	22-11/16 inches (575mm)
	36A41:	Width	38-3/16 inches (970mm)
		Height	30-1/16 inches (764mm)
		Depth	25-1/4 inches (641mm)
Mass	32A41:	74.5 lbs (33.8kg)
	36A41:	154 lbs (69.9kg)
Supplied accessories	Remote Control with 2 size “AA” batteries
Optional TV stand	32A41: ST3240
	36A41: ST3641

Design and specifications are subject to change without notice.

32

Contents

up Set Preparation Operation Basic Operation Advanced Section Reference CAUTION ATTENTION Note to CATV system installers in the USA Precautions Introduction Connecting your TV Preparing the remote control for use Location of controls on TV and remote control Using the remote control with a VCR or Set up Reference Section Advanced Operation Basic Operation Exploring your new TV 36A41 32A41 Audio and video cables are usually NOTE REGARDING PICTURE QUALITY When connecting video equipment, such as a VCR or DVD player: –For GOOD picture quality: Use regular video cables For BETTER picture quality: If your equipment has (continued) Connecting a cable converter box and a VCR Connecting a satellite receiver and a VCR Connecting a DVD player with component video and a VCR Connecting two VCRs •two pairs of audio cables (two single audio cables for mono VCRs) Section Installing the remote control batteries 1 Slide the battery cover off the back of the remote control 3 Slide the battery cover back onto the remote control until the lock snaps For details on the use of each control, refer to pages in brackets TV front panel Model 32A41 Model 36A41 Remote control Point the remote control at the VCR or cable TV converter Channel Number –If the correct code was entered, the VCR or converter will turn off If the correct code was entered –If the VCR or converter does not respond, repeat steps 1–4using another code If the VCR or converter does not respond to a different code VCR code table Cable TV converter code table Page Turning the TV set on Selecting the on-screendisplay language Understanding the Auto Power Off feature Understanding the Last Mode Memory feature TV/CABLE function CH PROGRAM function ADD/ERASE function 4 To add the channel: To erase the channel: Operation Basic Operation Selecting a TV channel Select a channel in one of the following two ways: ●Scan through the programmed channels in numerical sequence: –Press CHANNEL s to select the next higher channel RTN Adjusting the picture quality Pressing Selection To reset the Picture and Sound adjustments to the factory settings Selecting the color temperature The color temperature modes change the color tones of the picture 1 Press MENU until the Picture 2 menu is displayed on-screen 2 Press t or s until COLOR TEMPERATURE is displayed in purple 3 Press T or S until the desired mode is displayed in purple You can adjust the sound quality (BASS, TREBLE and BALANCE) to suit your taste Adjusting the sound quality 1 Press MENU until the Audio menu is POWERdisplayed on-screen 2 Press s or t until the item you want to Setting the off-timer Canceling the off-timer Stereo Sound: SAP: Surround Sound: Listening to stereo sound Activating the surround sound effect Listening to a second audio program (SAP) To deactivate the SAP feature: Programming your favorite channels Selecting your favorite channels Viewing captions or text Opening the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu Adjusting the V-CHIPCONTROL menu (continued) Unblocking programs temporarily BLOCK CHANNEL function Page Page For additional information, visit our web site: ATTENTION CANADIAN CONSUMERS: TOSHIBA AMERICA CONSUMER PRODUCTS, INC PRINTED IN USA