Getting started
Programming channels into the TV’s channel memory
Auto scan - digital only -
As new services are broadcast, it will be necessary to
Auto scan will completely
Manual scan - digital only -
If there were any missing channel after Auto Scan, these channels might be found by using Manual Scan described in this section. Also, if you do not live in Australia, you must use Manual Scan to scan those channels in your country.
1From the SCAN menu, press or to select Manual Scan, then press Q.
2Enter password using the Number buttons or press 0000 (which is the default password), then Manual Scan will appear.
Manual Scan
1Press M and or to select the SCAN menu.
2Use to select Auto Scan.
3 Press Q. If Password Status (- page 29) is |
Channel No.
Frequency
Bandwidth
Priority
6
1775000 KHz
7MHz
HIGH
Scanning...
Enabled, Password menu will be displayed. Enter |
your password using the number buttons or press 0000 |
(which is the default password). |
Start Scan
Signal Level | 100% |
|
|
Quality70%
SNR: 20dB
| Password |
Blocking active |
|
Enter PIN code |
|
To temporarily unblock |
|
Back | Watch TV |
4The Select Location will appear. Current location will be highlighted. Press or to select a state in which you live.
5Press Q, a confirmation screen will appear indicating that All existing channels will be deleted. Continue? select Yes.
Back Select Function | Watch TV |
3Press or to select the item you wish to adjust. For Australia, to adjust Frequency, you may refer to the latest channel table from local dealer. And the
Bandwidth is 7MHz and Priority should be set to HIGH. Then press or to select Start Scan and press Q to start scanning.
4If scanning was successful, Get Channel Success appeared for 2 seconds. Repeat to scan other channels as necessary.
5 If scanning was unsuccessful, Timeout Error appeared. |
6Press Q to start Auto tuning.
Auto Scan
Channel 6 found...
|
| 7 Digital | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital HD | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital 1 | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital 2 | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital 3 | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital Guide | ||
|
|
|
| |
Scan Status | 6/69 | |||
Scan Percentage
Back 
Select Function
NT
Watch TV
At this point you can rescan the signal or refer to the |
Signal Level bar and Quality for aligning the direction |
of the aerial to get the signal. Refer to your aerial installer |
if problem persists. |
Notes:
• Signal level refers to the input Radio Frequency (RF) signal |
strength as perceived by the TV. Note that too strong signal |
may cause erroneous readings. If you use an aerial booster |
and find that you still get a low signal level, your booster gain |
may be set too high. In this case, adjust the gain |
accordingly. You may also see the No Signal on the screen |
when the signal level is low. |
The above sample display shows Auto Scan in progress. The channel number is shown as
7When the search is complete, the TV will automatically tune to the lowest logical channel number.
Note:
After the Auto scan, the TV may have scanned identical channels being broadcast from different transmitters. You can verify this by previewing those channels in the Channel List with identical logical numbers and check on their physical channel numbers (- page 30). If you do find channels with the same logical channel numbers but different physical channel numbers, it is recommended that you skip these duplicate channels and keep only one channel with the best signal strength as indicated by the SNR indicator in the
• Quality refers to the quality of the received digital signal. A |
high value of quality means that there are few errors in the |
signal. In the same way, a low value of quality implies that |
there are a large number of errors in the signal, which may |
cause distortions in video and audio. |
14
