Getting started
Turning the TV on
Switching on the TV
Connect the power cord to a wall outlet, the ! power indicator lights in red (standby mode).
1Press 
on the remote control or ! on the TV right side panel, the ! power indicator lights in green.
Note:
If you watch black and white programmes when the colour system mode is set to Auto, colour noise may appear on the screen. In this case select the appropriate Colour system (For the system of each country or region, refer to pages 15 and 42).
Switching off the TV
2Press Q to proceed.
3The Select Location screen will appear. Press or to select the state in which you live.
Select Location
Australian Capital Territory
New South Wales
Northern Territory
Queensland
South Australia
Tasmania
Victoria
Western Australia
MENU Back Select Function | EXIT Watch TV |
4Press Q to start tuning. The Auto Scan screen will appear and the TV will automatically start to search for available stations. The progress bar will move along the line.
1Press 
on the remote control or ! on the TV right side panel to switch to the standby mode.
Notes:
• This TV is not fully disconnected from the main supply, as |
minute current is consumed even when ! is turned off. |
When the TV will not be used for a long period of time, such |
as during vacation or travel, remove the power plug from the |
wall outlet. |
• The TV will automatically turn itself off after approximately 15 |
minutes if it is tuned to a vacant channel or a station that |
completes its broadcast for the day. This function does not |
Auto Scan
Channel 6 found...
|
| 7 Digital | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital HD | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital 1 | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital 2 | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital 3 | ||
|
|
|
|
|
|
|
|
|
|
| 7 | Digital Guide | ||
|
|
|
| |
Scan Status | 6/69 | |||
Scan Percentage
Back 
Select Function
NT
Watch TV
work in external input or Blue screen Off mode. |
The TV will automatically turn itself off after approximately 2 |
hours if you do not operate the TV after turned on by on timer |
function. |
• If power is cut off while you are viewing the TV, the Last |
Mode Memory function turns on the TV automatically when |
power is applied again. If power is going to be off for a long |
time and you are going to be away from your TV, unplug the |
power cord to prevent the TV from turning on in your |
absence. |
Tuning the TV for the first time
- digital only -
Before switching on the TV, put your decoder and media recorder to Standby if they are connected and ensure the aerial is connected. To setup the TV use the buttons on the remote control as detailed on page 10.
1Press 
, the Welcome screen will appear. This screen will appear the first time that the TV is switched on and each time the TV is reset.
Thank you for choosing TOSHIBA television.
First you need to tune in your television.
Please ensure aerial is connected before proceeding.
Press 
to continue.
5When the search is completed, the TV will automatically tune to the lowest logical channel number. See the following for more details on Auto Scan.
Note:
If you do not live in Australia, press P at the Select Location. Press M, then press or to select PROFILE.
Press or to select Time Zone to set your time zone (- page 23).
Then use Manual Scan to start tuning (- page 14).
This integrated TV is equipped with both Digital and Analog system. To switch between Digital and Analog TV press ATV/DTV on the remote control.
Learning about the menu system
We suggest you familiarize yourself with the display charts before using the menu system:
•Press M to display menu, then press or to select main menu headings.
•Press or to select an item.
•Press or to select or adjust setting.
•Press Q to display the next menu.
12
