INSTALLATION
Attaching the water supply hose to the faucet
If you attach the water supply hose completely, it may cause a water leakage. | Branching |
| water pipe |
Faucet shape
Square | Movable | ||
shaped | faucet | faucet | faucet |
The distance is needed 1.6 cm or more
Caution
• The old inlet hose should not be reused.
• If the faucets are not suited, please contact your
dealer. |
|
• Do not connect the hot water supplying |
|
convenience. |
|
• In order to provide a permanent source of | Hose union |
water for your washing machine, it is suggested
that a branching water pipe (available separately) be used.
Attaching the hose union
Hose Union
5 Remove the seal from the union | Ring |
and turn to the arrow destination |
|
1 | Push the lock lever of the water |
| supply hose. Pulling the sleeve down, |
| lower the entire hose to disconnect |
| the hose union. |
2 | Check the diameter of the faucet. |
Lock lever
Water supply hose
Sleeve
the nozzle to tighten securely. |
|
6 Check the gap is approx. 1 to 3 | Approx. |
mm between the nozzle and the | 1 to 3 mm |
ring. | Nozzle |
• If the gap is wide, it may cause the water leak.
When the faucet mouth is large, |
loose the screws and remove the |
inside ring to facilitate, attachment. |
3 Loose 4 screws of the hose union, |
push the hose union to the water |
faucet. |
4 Tighten the four screws evenly |
around the faucet. In this time check |
the gap is approx. 4 mm between the |
nozzle and the ring. |
Inside ring
Ring
Approx. 4 mm
Joint seal
• If it cause the water leakage during operation, tighten the nozzle more securely.
Caution
•If you attach the hose union again because of moving house etc., loose the gap is approx. 4 mm between the nozzle and the
ring. Then attach it according
above methods. They are | Approx. |
preventable the water leakage. | 4 mm |
Connecting the water supply hose
1Pull the sleeve down, then insert the water supply hose.
2Separate the sleeve until a click is heard, then push it up.
3Check to ensure that the lock lever is hung on the nozzle. Next, check to ensure that the water supply hose does not come off by pulling down on it.
Lock lever
4Tighten the hose nut on the end of the
water supply hose Nozzle securely to the water
intake valve.
Sleeve | Water supply |
Hose nut | |
| hose |
Water intake valve
Caution
•Check to ensure that the water supply hose is properly installed by turning the water on and checking for leakage.
If there is leakage, connect it from the first.
•If you remove the water supply hose after supplying water, water may splash. Refer to the following
— “Removing the water supply hose”.
If the filling water becomes not good
The water inlet may be blocked by foreign objects. Remove the water supply hose and clean the filter with a brush.
•If you remove the water supply care- lessly, water may splash.Therefore, use the following procedure.
Filter
Water intake valve
Removing the water supply hose
1Turn the water faucet off.
2Turn the power switch ON and press the START/HOLD pad.
3After indicating the water level, loosen the hose nut of the machine top and remove it.
In case of water may freeze
Drain all water from the basket, drainage hose and water supply hose after using the machine.
If the water is frozen | under 40°C | ||
1 | Remove the water supply hose and pour in warm water (under 40°C). | ||
| |||
2 | Fill warm water (under 40°C) into the basket until the pulsator is |
| |
completely covered. Leave it for 30 minutes.Then check to see whether the pulsator can be turned by hand.
13
6348100701 | 13 | 22/10/08, 11:19 |
