Manuals / Toshiba / Computer Equipment / Barcode Reader

Toshiba B-SX6T Series, EO1-33056D Care must be taken not to pinch your fingers or hands

Models: B-SX6T Series EO1-33056D

1 139

Download 139 pages 60.26 Kb

Page 107

4. MAINTENANCE

ENGLISH VERSION EO1-33056

4.1 Cleaning

4.1.6 Optional Strip Module 1. Press down the Backing Paper Release Bar to open the Strip Unit.

WARNING!

Care must be taken not to pinch your fingers or hands.

Release Bar

2.Remove jammed media or backing paper, if any.

3.Wipe the Backing Paper Holder and the Strip Roller with a soft cloth slightly moistened with absolute ethyl alcohol.

Strip Roller

Backing Paper Holder

E4- 9

Image 107

Toshiba B-SX6T Series, EO1-33056D owner manual Care must be taken not to pinch your fingers or hands

Contents

SX6T Series Vorsicht CE Compliance for EU onlySX6T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction FeaturesWing Bolt 2 pcs AccessoriesSupply Holder Frame L Rear View DimensionsAppearance Front ViewInterior Operation PanelOption Name Type Usage OptionsManual threshold setting Printer SetupSetup Flow ProcedureAssembling the Supply Holder Frame InstallationExample of US Type Connecting the Power CordLoading the Media Open the Top Cover and the Right Side Cover Set the Head Lever to the Open positionMedia Guide Media Guide Screw Supply Holder Frame Detail of Fixed Sensor Fixed sensor Movable sensorDetail of Movable Sensor Feed Gap Sensor position adjustment Black Mark Sensor position adjustment Close the Top Cover and Right Side Cover Batch modeStrip mode Option Cut mode Option Tag paper or Thick paper Label or Thin mediaLoading the Ribbon Loading the Ribbon Close the Head Lock Plate, Right Side Cover, and Top Cover Connecting the Printer to Your Host Computer Turning the Printer How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedAfter selecting a character code, press the Pause key Character Zero SelectionCharacter Code Selection Use the Feed or Restart key to select a desired optionAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionFlow Control Code Selection Stop Bit Length SelectionParity Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionHead Up Cut Selection Control Code Selection Ribbon Save Function SelectionAfter selecting a ribbon type, press the Pause key Ribbon Type SelectionAfter selecting the Feed key function, press the Pause key Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionAfter selecting the media sensor type, press the Pause key Web Printer Function SelectionMedia Sensor Selection Expansion I/O Interface Type Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Label End/Ribbon End Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key After selecting the Back Feed Speed, press the Pause key Pre-Strip SelectionThis parameter is fixed to OFF Press the Pause key Reverse Feed Speed SelectionStabilizer Function Selection Maxi Code Specification SelectionStrip Motor Torque Selection This parameter is fixed to R0 Press the Pause keyAfter selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed While 6AUTO Calib is displayed on the LCD Message Display Press the Pause key to enter the Automatic Calibration ModeWhen 6AUTO Calib appears, press the Pause key Automatic CalibrationLAN Setting Time Setting Date SettingCont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys This parameter is to set a Gateway IP address Printer IP AddressThis parameter is to set an IP address Gateway IP AddressSocket Port Subnet MaskThis parameter is to set a Subnet Mask This parameter is to set a Dhcp client ID This parameter is to enable DhcpDhcp Dhcp Client IDAscii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-52 Windows 2000/XP E2-54 USB Interface E2-56 E2-57 E2-58 Finish button E2-60 E2-61 E2-62 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using an optional Cutter Module or Strip Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentTone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed keyRibbon End Sensor Adjustment Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Black Mark Sensor/Feed Gap Sensor Adjustment No media„ When using the Feed Gap Sensor „ When using the Black Mark SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line OperationPress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen MaintenanceCleaning When the Cutter Module is fittedPrint Head/Platen Pinch Roller Take out the Pinch Roller Ass’y from the printer Attach the Ribbon End Sensor Plate to the printer Plate with the Positioning Pins of the printerRe-install the Media Guides using the screws Covers and Panels Remove jammed media, if any Optional Cutter ModuleRemove the White Screw to detach the Media Guide Cutter Blade Care must be taken not to pinch your fingers or hands Restart key TroubleshootingError Messages Error Messages Problems/Cause Possible Problems Causes Solutions Possible ProblemsRibbon is not loaded properly Load the ribbon properly Cutter blade is dirty Clean the cutter bladeDo not use any tool that may damage the Print Head Removing Jammed MediaRemoving Jammed Media Model Printer SpecificationsThis section describes the printer specifications Available bar code types Label Supply SpecificationsMedia Media TypeTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective SensorMedia type Description RibbonRecommended Media and Ribbon Types Ribbon type Description Care/Handling of Media and RibbonRibbon type Combination of Media and RibbonAppendix 1 Messages and Leds Symbols in the messagePrinter did not succeed in writing data When the Dhcp function is enabledBase LAN Board is being initialised Dhcp client is being initializedFollowing message appears Receive buffer 1M byte Appendix 2 InterfacePIN ConnectorLED status Link LED Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 StandardSX708-RFID-U2-EU-R Serial interface Option B-SA704-RS-QM-RWireless LAN Option B-SA704-WLAN-QM-R Expansion I/O Interface Option B-SA704-IO-QM-R At least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeExpansion I/O Interface Appendix 5 GlossariesUSB Universal Serial Bus Device used to remove labels from the backing paperMedia and ribbon A3-1 Power switch 2-3 Pre-printed media 78, A5-1 Print head 1-4Index Index EO1-33056D