STUDIO206L/256/306/356/456 | Toshiba GD-1250, GD-1260, GD-1270

1.6.9e-STUDIO206L/256/306/356/456

e-STUDIO356/456

Saddle stitch

Finisher

MJ-1106/C

Finisher

MJ-1101

Inner Finisher

MJ-1032

Saddle stitch

Finisher

MJ-1033

2nd Line for

FAX Unit GD-1260

e-STUDIO356/456					e-STUDIO206L/256/356
	Reversing Automatic					Reversing Automatic
	Reversing Automatic					Reversing Automatic
Document Feeder (RADF)						Document Feeder (RADF)
	MR-3022					MR-3021

Bridge Kit

KN-2520

e-STUDIO356/456

Job Separator

MJ-5006

e-STUDIO206L/256/356

Job Separator

MJ-5004

Offset Tray

MJ-5005

FAX Unit

GD-1250

Drawer Module

MY-1033

Paper Feed

Pedestal (PFP)

KD-1025

Large Capacity

Feeder (LCF)

KD-1026

Fig. 1-10

GD-1210/1250/1270/1160/1260	© 2006 - 2011 TOSHIBA TEC CORPORATION All rights reserved
SPECIFICATIONS AND OUTLINE OF SYSTEM

1 - 18

11/12

Image 26

Toshiba GD-1250 STUDIO206L/256/306/356/456, Saddle stitch Finisher MJ-1106/C, Inner Finisher MJ-1032 Saddle stitch MJ-1033

Contents

GD-1210/1250/1270/1160/1260 Trademarks Transportation/Installation General Precautions at Service When the option has been installed VorsichtPage Contents Installation Explanation to the Users FAX Options Models FAX unit 2nd line for FAX unit Folio SpecificationsOriginal size Embedded DBm to -8 dBm The setting can be changed by 1 dBTransmission system DBm to 0 dBm Level -55 dBm or lower cannot be detected Comp Paper size Dimension width x length Printing areaST-R Features 11/04 Accessory GD-1210 GD-1250 GD-1270 Accessories and PartsFollowing accessories and parts come with the FAX unit Parts GD-1210 GD-1250 GD-1270 Extends the FAX functions when the FAX unit is installed Options Option Function STUDIO206L/256/306/356 Ments to be output System List STUDIO2500c/3500c/3510c STUDIO2330C/2820C/2830C/3520C/3530C/4520C NA/AU/EU/C/TW STUDIO5520C/6520C/6530C STUDIO205L/255/305/355/455 Offset Tray MJ-5005 STUDIO555/655/755/855 NA/EU-N/AU/C STUDIO2040C/2540C/3040C/3540C/4540C Pedestal PFP Feeder LCF KD-1027/C KD-1028 A4/LT/C STUDIO5540C/6540C/6550C STUDIO556/656/756/856 Inner Finisher MJ-1032 Saddle stitch MJ-1033 STUDIO206L/256/306/356/456Saddle stitch Finisher MJ-1106/C Reversing automatic document feeder LINE2 connector Line connector TEL connectorOverview Drawers Line connectorTEL connector STUDIO5520C/6520C/6530C, e-STUDIO5540C/6540C/6550C Power switch TEL connector Line connector LINE2 connector STUDIO205L/255/305/355/455, e-STUDIO206L/256/306/356/456 Power switch LINE2 connector Line connector TEL connector STUDIO555/655/755/855, e-STUDIO556/656/756/856 FAX FAX PWR Symbol Name FunctionLayout of PC Boards NCU MDM FAX FAX PWR Recording Mode LSU-RELATED Functions Printing algorithm Recording Paper Selection Algorithm and Printing AlgorithmRecording paper selection algorithm ST against A3/B4/A4/LD/LT size originals respectively OFF Effective printing lengthDiscard function Length of B Discard parameter Set value B4, A3 A4, B4 B5, B4 A5, A4 A5 , Comp LT, Comp COMP, LD LG/LT, LD ST, Folio B5, Folio Setting for the split recording Recording Paper and Function Priority Table of the recording paper selection modesOthers Receiving FAX document, or by Energy Saver ModeUser Functions Energy Saver Memory Reception YES Circuit Connection and Procedure to Change ModeDial call-up transmission to a telephone circuit Standby state Communication mode Toshiba original procedure Selection of the communication modeProcedure to select the transmission mode Telephone circuit This signal can be sent manually Signal form Signaling System Diagram and Signal FormsCircuit control signals Signal name Signal form Communication with the binary signals Mode change possible Informing that there is the next Image signalMode change is possible only for the original set manually Receiver Only error frame retransmitted 1 completed 2 completed Frames received Error occurred CFR JOB Status button Cancel buttonCED Nsfcsidis MCF Binary signals PRI-EOM PIPPIN PRI-MPS Format When this frame is the last frame, X =FCF FIF FCS FCF format of each binary signal Binary signal Format TCF 9600 bps, 7200 bps4800 bps, 2400 bps 3 V.8/V.34 communication sequence Standard procedure Transmitter Receiver Line closed Signal name Abbreviation Function Remarks 150 Hz Tone signal betweenHz and 3,750 Hz in units Data transmission TRN ALT Receives an NSF sent from FlagMaintains the synchroniza 7E H Tion Transmitter Is completed Image data Image data are sent. TransmitterScrambled data frame to be Encoded image data Turn off Scrambled 1 is sent for Transmission of one Is completed Flag Short training SignalPPS-EOP Informs to disconnect the line Line closed DIS cannot be recognized Transmitter Receiver Transmitter Receiver DIALING/COMMUNICATION Control DIALING/COMMUNICATION Control FAX mode FAX Automatic SwitchingTEL mode General functions Configuration GD-1210 GD-1160 GD-1250 / GD-1270 GD-1260 Configuration Description of Circuits EU/AU/AS/C models CML1 Line path switching control circuitSignal Name Type Active Description Destination ATT3DB1 IC5 RLY3, IC3IC3 Line 1 Dial Pulse Generation Signal Q53 Dial pulse generation circuit Line 1 Dial Pulse Generation Signal Line current detection circuit Line Current Detection Signal IC29 IC26Line Reverse Current Detection Signal IC29 IC26 REVA1 Line 1 Current Detection Signal IC29 IC26 Current Reverse Line 1 Current Detection IC29 IC26 Signal Line 1 CI Detect Signal IC29 IC26 CI detection circuit Line 1 CI Detection Signal IC29 IC26 Line monitor circuit NCU board Line1 Line Monitor Monitoring signalRinger/Alarm LOW High Relation between the signals and sound volume is as follows Sound volume PC Boards PWA-F-FAX-631 GD-1210 PWA-F-FAX-670 GD-1250/1270 08/04 08/04 PWA-F-MDM-563 GD-1160 PWA-F-MDM-671 GD-1260 PWA-F-FAX-POWER-631 GD-1210 Electrical Circuits Installation Explanation to the Users Installation