Toshiba SD-4960SU Troubleshooting, Table of Brand Codes, Setting Control Codes, Problem, Action

Toshiba-SD-4960(gb) 5/19/04 10:50 AM Page 34

Controlling a TV with the Remote

The remote control can be compatible with various brands of TV by setting their control codes. The TOSHIBA code has initially been set to control

Table of Brand Codes

Troubleshooting

Before requesting service (troubleshooting), please check the following.

TOSHIBA TVs.

Setting Control Codes

1.Press TV to set the remote control operating your TV.

2.While holding down PROG. button enter the two diglts of your TV’s brand code (listed right) using number buttons.

3.Release PROG.

4.Point the remote control at your TV and use each button listed below to make sure your TV is operated correctly.

TV POWER	To turn the TV on or off.
CH	To select TV channels in the
	upper or lower direction.
TV VOL.	To adjust the sound level.
I.SELECT	To select an external source
	such as a VCR.
Number buttons	To select TV channels.
	When selecting channels 1 to
	9, first enter 0 and then the
	desired number.

BRAND	CODE
TOSHIBA	PROG + 01
RCA/GE	PROG + 02
SONY	PROG + 03
MITSUBISHI	PROG + 04
JVC	PROG + 05
HITACHI	PROG + 06
PANASONIC A	PROG + 07
SHARP NEW	PROG + 08
SANYO	PROG + 09
MAGNAVOX	PROG + 10
GOLDSTAR NEW	PROG + 11
SAMSUNG	PROG + 12
SHARP OLD	PROG + 13
ZENITH	PROG + 14
PANASONIC B	PROG + 15
PIONEER	PROG + 16

Problem

No operations can be performed with remote.

Disc does not play.

5.1channel sound is not being reproduced.

The	icon appears on
screen.

Disc Menu doesn’t appear.

Play mode differs from the Setup Menu selection.

Action

•	Check the batteries in the remote. They may need replacing.
•	Operate the remote control at a distance of no more than 20 feet.
•	Operate the remote control within 30° angle on either side of the
	remote control sensor.
•	Remove batteries and hold down one or more buttons for several
	minutes to drain the microprocessor inside the remote to reset it.
	Reinstall batteries and try to operate the remote again.
•	Ensure that the disc is installed with the label side facing up.
•	Check the region number of the DVD.
•	5.1 channel sound is reproduced only when the following condi-
	tions are met. :
	1) The DVD player is connected with the proper amplifier
	2) The disc is recorded with 5.1 channel sound.
•	Check whether the disc being played has the “Dolby 5.1 ch” mark
	on the outside.
•	Check if your audio system is connected and working properly.
•	In a SETUP Menu, is the Audio Output set to Bitstream?
•	The features or action cannot be completed at this time because:
	1. The DVD’s software restricts it.
	2. The DVD’s software doesn’t support the feature (e.g., angles).
	3. The feature is not available at the moment.
	4. You’ve requested a title or chapter number or search time that
	is out of range.
•	Check if the disc has a Menu.
•	Some of the functions selected in the Setup Menu may not work
	properly if the disc is not encoded with the corresponding function.

Page

P5

P7

P11

P29~30

P14

P27~33

100To substitute for 100 channel key.

DISPLAY	To turn on or off TV’s screen
	display.
ENTER	To use for the TV’s ENTER
	key.

Important Note

•Some TV’s may not respond to all the operations above, or may not be operated at all with this remote control. In this case, operate your TV with its own remote control.

•For some brands, several control codes (brand codes) are allocated. Try each of them until the buttons work on your TV.

•If you replace the remote control’s batteries, set the brand code again.

The screen ratio cannot be changed.

No audio.

The screen is blocked

Forgot password

If you experience other problems.

•	The Screen Ratio is fixed on your DVD discs.
•	Make sure you have selected the correct Digital Output in the
	Audio Options Menu.
•	Press power on from a cold start with no disc in the unit. Press the
	STOP (	) and PLAY (	) buttons simultaneously on the front
	panel for three seconds. The SELECT MENU LANGUAGE display
	will appear. Select the number button of the desired language.
•	Press power on from a cold start with no disc in the unit. Press the
	STOP (	) and PLAY (	) buttons simultaneously on the front
	panel for three seconds. The SELECT MENU LANGUAGE display
	will appear. Select the number button of the desired language.
	Press the SETUP select Setup, then press RIGHT or ENTER.
	Press Up or Down to select Parental Setup. The Parental Setup is
	now unlocked as indicated on the display. You can change your
	password.
•	Go to the contents and find the section of the instruction book that
	contains the explanations regarding the current problem, and follow
	the procedure once again.
•	If the problem still cannot be solved, please contact your nearest
	authorized service center.

P31

P29~30

P31~32

P32~33

-

ENG-34 ENG-35