16. ERROR MESSAGE TABLE

 

 

 

 

 

 

 

 

 

16. ERROR MESSAGE TABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CMT Operation Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Message

 

 

Cause

 

Solution

 

 

 

 

 

 

 

 

 

Mismatch of the model type.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mismatch of the base unit.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MISMATCH SCALE SPEC

Mismatch of the VERSION.

Press the

CLEAR

key.

 

 

 

 

 

 

 

 

 

Mismatch of the

 

 

 

 

 

 

 

 

 

 

 

 

TRANSMITTING DATA.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mismatch of the scale capacity.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parity error

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Framing error

 

 

 

 

 

 

 

 

 

BAD TAPE OR CMT

 

 

Press the

 

key.

 

 

 

 

 

 

 

Overrun error

CLEAR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Data error

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Two or More Hardware error

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIME OUT ERROR

 

Time out error

Press the

CLEAR

key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LON System Mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Error message

 

 

 

Cause

 

Solution

M

BM/S

 

 

COMMUNICATION

 

1. The power of the master or

1. Turn the power of the master

 

 

 

 

 

 

ERROR

 

 

backup master scale is not

or backup master scale ON.

 

 

 

 

 

 

 

 

 

turned ON.

Connect them with each

 

 

 

 

 

 

 

 

 

They are not connected with

other or turn the scale in-line.

 

 

 

 

 

each other or in off-line state.

2. Call your authorized service

 

 

 

 

 

 

 

 

2. LON cable is broken.

representative.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEQUENCE ERROR

 

The power was not turned OFF and

Turn the power switch OFF and

 

 

 

 

ON again after setting ID #.

ON again.

 

 

 

 

 

 

 

 

 

 

SEQUENCE NO.

 

Text data number is incorrect.

Call your authorized service

 

 

ERROR

 

 

 

 

representative.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MASTER BUSY

 

Registration job is performed on a

1. Quit reset job on the master

 

 

 

 

 

 

 

 

satellite scale while reset job is

scale.

 

 

 

 

performed on the master scale.

2. Quit registration job on the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

satellite scale.

 

 

 

 

 

 

BACKUP MASTER

 

The backup master does not have

Down load PLU from the master

 

 

 

 

 

 

NOT RESET

 

same PLU with the master scale.

to the backup master scale.

 

 

 

 

 

 

 

Then run the reset operation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

again.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEXT ERROR ##

 

1. Error text is found.

Call your authorized service

 

 

 

 

 

 

 

 

02:

Sequence No. error

representative.

 

 

 

 

 

 

 

 

05:

LRC error

 

 

 

 

 

 

 

 

 

 

 

08:

Text error

 

 

 

 

 

 

 

09:

Command error

 

 

 

 

 

 

 

 

 

 

 

2. The master scale differs from

 

 

 

 

 

 

 

 

 

 

 

 

other scale in ROM version.

 

 

 

 

 

 

 

 

 

 

 

 

 

M: Master scale BM: Backup master scale S: Satellite scale

16- 3

Page 92
Image 92
Toshiba SL-9000 owner manual LON System Mode