Toyota EPS9000 START POINT RETURN MODE

OPERATION

PROCEDURE

START POINT RETURN MODE

This operation moves the embroidery hoop t o the start point [*1]

1 Select the start point return operation.

2 Press [SET] to confirm the selection.

If the hoop is returned to the start

point during embroidering, embroi-

dery cannot be continued.

The hoop moves to the start point

position when the SET key is

pressed.

3 End of operation

*1: Start point is the start point of design. If automatic offset is set, the offset start position is taken as the start point.

CAUTION

When performing this operation, do not put your hands or others

under the needle or on the table.

Otherwise, you could get hurt when the needle or hoop has

moved.

FD07

***** EMB PAUSE ****

AISIN123.10O 1

58/ 1027

01/15: 23456789AB<D>

Press .

***** EMB PAUSE ****

CANCEL EMB ?

［Y=SET,N=ESC］

Press .

***** EMB START ****

AISIN123.10O 1

0/ 1027

01/15: 23456789AB<D>

Contents

Main TOYOTA COMPUTERIZED EMBROIDERY SYSTEM INSTRUCTION MANUAL Page CONTENTS PREPARATION OPERATION PROCEDURE OPERATION BASICS FUNCTION MENU ! ! ! DANGER WARNING ! Page SAFETY ! SAFETY ATTEN TIO N ! FD07 PRECAUTIONS Positions and Contents of the Warning Labels DANGER PART NAMES CHECKING THE PARTS ACCESSORIES Page EMBROIDERY MACHINE OPERATION PANEL BOX DIP SWITCHES DIP switch ON or OFF is set as follows: ON * Access to the Embroidery Information 1 2 3 4 5 6 7 8 ON PREPARATION ASSEMBLING CARRYING INSTALLATION WIRING WARNING CONNECTING THE FDD (FLOPPY DISK DRIVE) (TO BE PURCHASED SEPARATELY) SETTING THE UPPER THREAD Upper Thread Setting Procedure TOYOTA SETTING THE UNDER THREAD SETTING THE FABRIC ON THE HOOP SETTING THE HOOP TO THE EMBROIDERY MACHINE Page WINDING THE UNDER THREAD CHECKUPS BEFORE STARTING OPERATION CHECKING THE EMBROIDERY HEAD Check of the Color Change Device and Set Screw Check of Needle Lowered Position OPERATION PROCEDURE OPERATION BASICS STARTING AND STOPPING THE MACHINE Power Switch EMERGENCY STOP Switch STEPS TO START EMBRODIERY Page SCREENS Page Page Page Page Page FUNCTION MENU CHANGING DISPLAY THREAD BREAK SENSOR BOBBIN COUNTER (SET) BOBBIN COUNTER (COUNTER) LOCK STITCH SATIN ADJUSTMENT SLOW START TRIMMING IN JUMP JUMP LENGTH TRIMMING LENGTH TRIMMING TIMING COMMUNICATION SPEED HOOP MENU HOOP MODE INITIALIZATION START POINT RETURN MODE MANUAL SPEED HOOP TIMING OFFSET EDIT DESIGN ROTATION MIRROR DESIGN REPEAT Page COLOR CHANGE SETTING COLOR CHANGE MODE NEEDLE BAR SETTING (INPUT) + + 1 1 0 NEEDLE BAR SETTING (CHANGE) + 1 1 0 PAUSE SETTING DATA SET MENU DATA INPUT (FLOPPY DISK) + DATA INPUT (PC) Page DATA SELECT DATA DELETION MEMORY MODE MEMORY INITIALIZATION MANUAL OPERATION COLOR CHANGE START POINT RETURN MODE TRACE OFFSET (POSITION SETTING) OFFSET (HOOP TRAVELING) TRIMMING HOOP FORWARD/BACK (TRAVEL UNITS) HOOP FORWARD/BACK (n-STITCH FEED) HOOP FORWARD HOOP BACK OUTLINE OF FUNCTIONS ROTATION MIRROR REPEAT OFFSET 1. Manual Offset 2. Automatic Offset SATIN ADJUSTMENT TRACE TROUBLESHOOTING AND MAINTENANCE DAILY MAINTENANCE Maintenance Stop WARNING Cleaning Lubrication Greasing PROGRAM INSTALLATION [When installing from personal computer] Page Page [When installation from FDD] Page IF MACHINE OPERATION IS INTERRUPTED 1 2 3 4 5 6 7 8 10 11 12 13 14 IF MACHINE STOPS DUE TO OCCURRENCE OF A TROUBLE SPECIFICATION