![Installing Twisted-Pair 10BASE-T Cable](/images/new-backgrounds/111422/11142221x1.webp)
Installing Twisted-Pair 10BASE-T Cable
To connect
1.Locate or build
•802.3 compliant (See page 20.)
•with straight through connector/cable configuration (See page 7.)
•with male
2.Connect male
3.Connect male
NOTE: The IEEE 802.3 standard states that the shield of a coax trunk cable shall make electrical contact with an earth reference once and only once per segment. Failure to provide an earth ground to a 10BASE- 2 or
10BASE-2 Requirements
Thinnet
NOTE:
wall plate
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| X – 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
| ||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
With a maximum segment length of 185 meters and a minimum segment length of 0.5 meters, the coaxial cable must have a 50 ohm characteristic impedance. Standard BNC connectors and "T's" provide access to the media, typically connected directly to the back of network interface cards, eliminating the need for an external transceiver.
Only 30 transceivers can be installed onto a
10BASE-5 Requirements
Thicknet
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
X – 1 | 2 | 3 | 4 | 5 | 6 | 7 |
| 8 |
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
X – 1 | 2 | 3 | 4 | 5 | 6 | 7 |
| 8 |
| X – 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
With a maximum segment length of 500 meters and a minimum segment length of 1.5 meters,the coaxial cable must have a 50 ohm characteristic impedance.
As many as 100 transceiver can be installed onto a
11 | LANMaster™ T8 | 8 |