Transition Networks S4TEF10xx-11x specifications SBFTF10xx-10x, Operation -- Continued

SBFTF10xx-10x

Operation -- Continued

Setting the password:

1.At the prompt, press the letter “P” key.

2.At the prompt, type any alphanumeric combination (8 characters maximum)

3.Press the ENTER key: the password is set.

Important: After setting up or changing command parameter(s) you must save the change(s) before exiting the screen or the change(s) will not go into effect.

To show the current configuration:

1.At the prompt, press the letter “D” key.

2.Press the ENTER key and the current configuration will appear as shown below:

----Local Device ---- SN: 676. Mode: Software

Ethernet: AutoNeg, 100Mbs, HD, LPT

T1/E1 #1: DSX-1 0-133, Xmit AIS, AMI,

T1/E1 #2: DSX-1 0-133, Xmit AIS,

T1/E1 #3: DSX-1 0-133, Xmit AIS, AMI,

T1/E1 #4: DSX-1 0-133, Xmit AIS,

Serial : 9600, No Parity

DMI: Not Detected. VLAN: Disabled

----Remote Device ---- SN: 676. Mode: Software

Ethernet: AutoNeg, 100Mbs, FD, LPT

T1/E1 #1: DSX-1 0-133, Xmit AIS,

T1/E1 #2: DSX-1 0-133, Xmit AIS,

T1/E1 #3: DSX-1 0-133, Xmit AIS,

T1/E1 #4: DSX-1 0-133, Xmit AIS,

Serial : 9600, No Parity

DMI: Not Detected.

->

Operation -- Continued

To show the configuration menu for the local device:

1.At the prompt, type the letter “C,” press the spacebar, then type the letter “L.”

2.Press the ENTER key and the local device configuration menu will appear as shown below:

Note: In this menu, the T1/E1/J1 commands for local loopback, for example, type the command this way: LL, press the spacebar, then type the port number, press spacebar, then type the

number of the command, in this case (1= enable or 2 = disable).

The command sequence IS NOT case sensitive.

Local Device Configuration Menu:

*T1/E1/J1:

LLx 1 - Local Loopback on T1/E1/J1 Port x ENABLE LL x 2 - Local Loopback on T1/E1/J1 Port x DISABLE RL x 1 - Remote Loopback on T1/E1/J1 Port x ENABLE RL x 2 - Remote Loopback on T1/E1/J1 Port x DISABLE XE x - Enable Transmit AIS on LOS for Port x

XD x - Disable Transmit AIS on LOS for Port x EB x - Encoding set to B8ZS on Port x

EA x - Encoding set to AMI on Port x *RS-232:

B x - Serial port baud rate

(1=9600, 2=19200, 3=36400, 4=57600) *Enet 10/100:

A1 - Autonegotiation ENABLE

A2 - Autonegotiation DISABLE

TLPT1 - Transparent Link Pass Through ENABLE TLPT2 - Transparent Link Pass Through DISABLE

F10 - Force 10Mbps

F100 - Force 100Mbps

FF - Force Full Duplex

FH - Force Half Duplex

S- Save new Configuration and Exit

Q - Exit without saving Configuration ->

14 24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 15