Troy-Bilt 630CN Featuresandcontrols, Introduction, Engine Controls, Wheel Drive Pins, Freewheel

SECTION3: FEATURESANDCONTROLS

WARNING: Before operating your machine, carefully readand understand all safety, controls and operating instructions in this Manual,the separateEngine Owner'sManual,and on the decalson the machine. Failureto follow these instructions can result in serious personal injury.

INTRODUCTION

This Section describes the location and function of the controls on your tiller. Re- fer to the following Section, Operationfor detailed operating instructions.

Practice using these controls, with the en- gine shut off, until you understandthe op- eration of the controls and feel confident with each of them.

ENGINE CONTROLS

Referto the enginemanufacturer'sEngine Owner'sManual (included in the tiller liter-

Forward

Reverse ClutchControl

(Models634F/634B)

DepthRegulator

Handlebar Height Adjustment

Wheel Drive Pin (oneachwheel)

Figure3-1: Tillerfeaturesandcontrols(5. HPModelshown). SeeS_eparateEngineOwner's Manual toidentifyenginecontrols.

ature package)to identify the controls on your engine.

IMPORTANT:Thecontrol for stopping the engine is located on the engine.

WHEEL DRIVE PINS

Eachwheel is equippedwith a wheel drive pin (A, Figures3-2 and 3-3) that secures the wheel to the wheel shaft (B). The wheelscan be positioned in either a WHEELDRIVEora FREEWHEELmode.

WARNING: Neverallow either of the wheelsto bein the FREEWHEELposition when the engineis running. Always put both wheelsin the WHEEL DRIVEposition beforestarting the engine.

Failureto comply could cause loss of tiller control, property damage,or personal injury.

Beforestarting the engine,put both wheels in the WHEELDRIVEposition by inserting the wheel drive pins through the wheel hubs and the wheel shaft. Doing so "locks" the wheels to the wheel shaft, causingthe wheelsto turn when either the

Forward Clutch Bail (all models) or the Re- verseClutch Control (Models 634F and 634B) is engaged.

Usethe FREEWHEELmode only when the engineis not running. In FREEWHEEL,the wheel drive pins are placed only through the holes in the wheel shaft (not the wheel hubs), thus allowing the wheels to turn freely when you manually movethe tiller.

To place the wheels in WHEELDRIVEor

FREEWHEEL:

1.Stop engine,disconnectsparkplugwire from spark plugandallow engineto cool.

_	tiller on its side when changing
	ARNING:	Do not place

wheeldrive positions. Doing so could result in gasoline leaking from the fuel tank.

Failureto follow this instruction could result in personal injury or property damage.

2. Raiseonewheel about one inch off the

ground and placea sturdy support under the transmission.

3.Removehairpin cotter (C, Figures3-2 and 3-3) from wheel drive pin (A).

4.FORWHEELDRIVEMODE(Figure3-2): Slide wheel outward and align holes in

10

Figure3-2: WHEELDRIVE position.

wheel hub (D, Figure 3-2) and wheel shaft (B). Insert wheel drive pin (A) through wheel hub (D) and wheel

shaft (B). Securewheel drive pin with hair- pin cotter (C) by pushing hairpin cotter in as far as it will go. Repeatwith the other wheeland then remove the support from beneaththe transmission.

5.FORFREEWHEELMODE( Figure3-3): Slidethe wheel inwardand insertthe wheel drive pin (A, Figure3-3) only through the hole in the wheel shaft (B). Secure wheel drive pinwith hairpincotter (C) by pushing hairpin cotter in as far as it will go. Repeat for the other wheel and then remove the support from beneaththe transmission.