FC-890 Flying Chains, TS-890 Tilting Straps | Turbosound LMS-D24

user manual

TA-890

FC-890 Flying Chains

An adjustable length flying chain, consisting of a top hook, chain with adjusting choke, and a cabinet link, is used to connect the cabinets to the flybars. The top chain from the flybar to the first cabinet can be adjusted to gain more height on the system and also improve the looks. Alternatively if you are flying four or more cabinets deep with a lot of kelp it is good to give the top chain some additional length as this makes racheting easier.

Chains are universal (not handed) and therefore can be used for either side of the cabinet. FC- 890 flying chains are load tested to 560kg.

TS-890 Tilting Straps

0.59m

4m

The tilting strap, TS-890, is in two parts. The longer part is attached to the tilt strap point on the flying bar using the buckle at its end. The other part of the strap with the ratchet is hooked into the tilt strap point on the underside of the bottom enclosure. The free end is then threaded through the ratchet and the strap tightened to achieve the desired tilt. The tilt strap is designed to ratchet in both directions so that the amount of tilt on a column may easily be increased or reduced incrementally.

TA-890 user manual

Page 31

Image 31

Turbosound LMS-D24, LMS-D6, LMS-D26 user manual FC-890 Flying Chains, TS-890 Tilting Straps

Contents

Aspect TA-890 System TA-890 TA-890 TA-890 Amplifier Rack Signal Wiring Output Connections Products EC Declaration of Conformity Turbosound Aspect System Concepts IntroductionTurbosound Polyhorn TA-890 Aspect TA-890 Turnkey System Concept Amplifier Racks Power AmplifiersLoudspeaker Management System LMS Concept LMS-D24, LMS-D26 and LMS-D6 Loudspeaker Management Systems Aspect Loudspeaker Components Digital ControllersTA-890L Low Frequency Enclosure TA-890H Mid-high Enclosure TSW-218 Subwoofer TA-890 Transportation Aspect Flying Systems Overview Flying and Stacking Gigmate Acoustic Simulation Setting up a Venue Overview Running Turbosound GigMate / Ease Focus for the first time System Setup Designing a system TA-890 TA-890 Changing the system Theatre-style venue 3-wide flown cluster @ 1kHz Safety Notes on Rigging Sample Certificate of Load Test Flying Hardware Wide and Narrow Flybar Settings Single A-System Flybar FB-890/1A TOP View Bottom View Figue 3. Triple ‘A’ System Flybar FB-890A/3W TS-890 Tilting Straps FC-890 Flying Chains TA-890 Four-wide hang using MB-890 and FB-890/2A ‘A’ System Flygear Integral Flying Hardware Swing Latch Connecting Flying Chains to the CabinetConnecting Cabinets ‘A’ System Drop Link Setting Vertical Angles ‘A’ System Attach buckle Attaching the Tilt Straps Bass Enclosure arraying Turbobass DirectivityAiming directivity of the stack TA-890 ABC DEF Typical Left to Right problem Bass in a line Creating Directional Bass arrays Fanned bass General observations of long lines of bass Bessel Array End firing array Summing up Ground stacking Introduction General features & facilities UnpackingMechanical Installation LMS Series Loudspeaker Management Systems LMS-D6 Front Panel Functions LMS-D6 Rear Panel Functions Mains Power Powering Up Voltage SettingSafety Earthing AC Power Fusing Time correction for loudspeaker driver placement Input and Output Connector WiringAudio Connections LMS-D24 and D26 Loudspeaker Management Systems Features Front Panel Functions TA-890 Rear Panel Functions Creating a Crossover Selecting a Factory PresetOperating the LMS-D24 and D26 Starting up Navigation and Viewing Parameters A Freq Width Gain EQ1 100Hz 1.4Q 0.0dB Navigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB Presets Preset Recall Preset Store Preset Name Store My System Stereo / Mono Formats Input DSP block diagramOutput DSP block diagram DSP Processing Layout Input Channels DSP Processing A Freq Shape HPF 20.0Hz LR24 High and Low shelving filters Parametric EqualisationParametric filters Output Channels DelayGain and Polarity High and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24 Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing Limiters Utility functions Utilities Audio Input Connectors Racking, Cables and Connections AMP-890 Aspect System Amplification Rack Input Connections Options Output Connections Amplifier Rack Signal Wiring Mid-High Outputs Break-out Cables NL4 bass Extension Cables Break-out cables NL8 mid-high Mains Connections General Features & Facilities T-45 High Efficiency Audio Power Amplifiers Front Panel Functions T-25 Front Panel Functions T-45 Mechanical Installation Audio Connections & Controls Voltage Range Polarity Gain and Sensitivity SettingsInput Impedance Damping Factor Attenuation & Gain Setting Cooling System Long Speaker Lines Maintenance To rotate the horn moulding from ‘A’ mode to ‘B’ mode Removal of the high frequency driver To rotate the horn moulding from ‘B’ mode to ‘A’ mode Removal of the high-mid frequency driver Removal of the low-mid frequency drive units General Maintenance Paintwork TA-890 Technical Specifications Serial Numbers Warranty TA-890