LMS-D6 Rear Panel Functions, Mains Power | Turbosound LMS-D24

user manual

TA-890

LMS-D6 Rear Panel Functions

RS232

DATA INPUT

PROTECTION AGAINST FIRE REPLACE ONLY WITH THE SAME TYPE T1A, 250V FUSE

WARNING / AVIS

DO NOT EXPOSE TO RA IN OR MOIST URE THIS EQUIPMENT MUST BE EARTHED SHOCK HAZARD – DO NOT REMOVE COVERS

RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

CUSTOM MADE FOR TURBOSOUND INTHE UK BY XTA ELECTRONICS

OUTPUT 6	OUTPUT 5	OUTPUT 4	OUTPUT 3	OUTPUT 2	OUTPUT 1	INPUT B	INPUT A

PIN1=SHIELD

PIN2=HOT

PIN3=COLD

1

2

3

4

5

1.Power Switch.

2.Mains Fuse - Located in a finger-proof fuseholder adjacent to the mains inlet. Always replace this fuse with the correct type as shown on the rear panel legend. (N.B. A spare fuse is located in this holder.)

3.Mains Power - Connected via a standard IEC socket. A compatible power cord is supplied with the unit.

4.External - RS232 via a 9-pin DIN DEE socket, for connection to a PC.

5.XLR Inputs and Outputs - 3 pin XLR connectors are provided for each audio input and output. All terminations are fully balanced, pin 2 Hot, pin 3 Cold and pin 1 not connected.

Mains Power

The LMS-D6 must always be connected to a 3 wire grounded AC supply. It is supplied with a standard IEC power cord with conductors as follows:

BROWN	Power line Live (Phase)
BLUE	Power line Neutral
GREEN/YELLOW	Safety Earth and ground connection

Units supplied to the North American market are fitted with an integral moulded 3 pin connector, which is provided to satisfy UL & CSA safety standards.

TA-890 user manual Page 49

Image 49

Turbosound LMS-D24, LMS-D26 user manual LMS-D6 Rear Panel Functions, Mains Power

Contents

Aspect TA-890 System TA-890 TA-890 TA-890 Amplifier Rack Signal Wiring Output Connections Products EC Declaration of Conformity Turbosound Aspect System Concepts IntroductionTurbosound Polyhorn TA-890 Aspect TA-890 Turnkey System Concept Loudspeaker Management System LMS Concept Power AmplifiersLMS-D24, LMS-D26 and LMS-D6 Loudspeaker Management Systems Amplifier Racks Aspect Loudspeaker Components Digital ControllersTA-890L Low Frequency Enclosure TA-890H Mid-high Enclosure TSW-218 Subwoofer TA-890 Transportation Aspect Flying Systems Overview Flying and Stacking Gigmate Acoustic Simulation Setting up a Venue Overview Running Turbosound GigMate / Ease Focus for the first time System Setup Designing a system TA-890 TA-890 Changing the system Theatre-style venue 3-wide flown cluster @ 1kHz Safety Notes on Rigging Sample Certificate of Load Test Flying Hardware Wide and Narrow Flybar Settings Single A-System Flybar FB-890/1A TOP View Bottom View Figue 3. Triple ‘A’ System Flybar FB-890A/3W TS-890 Tilting Straps FC-890 Flying Chains TA-890 Four-wide hang using MB-890 and FB-890/2A ‘A’ System Flygear Integral Flying Hardware Connecting Cabinets ‘A’ System Connecting Flying Chains to the CabinetDrop Link Swing Latch Setting Vertical Angles ‘A’ System Attach buckle Attaching the Tilt Straps Bass Enclosure arraying Turbobass DirectivityAiming directivity of the stack TA-890 ABC DEF Typical Left to Right problem Bass in a line Creating Directional Bass arrays Fanned bass General observations of long lines of bass Bessel Array End firing array Summing up Ground stacking Mechanical Installation General features & facilities UnpackingLMS Series Loudspeaker Management Systems Introduction LMS-D6 Front Panel Functions LMS-D6 Rear Panel Functions Mains Power Safety Earthing Voltage SettingAC Power Fusing Powering Up Time correction for loudspeaker driver placement Input and Output Connector WiringAudio Connections LMS-D24 and D26 Loudspeaker Management Systems Features Front Panel Functions TA-890 Rear Panel Functions Operating the LMS-D24 and D26 Selecting a Factory PresetStarting up Creating a Crossover Navigation and Viewing Parameters A Freq Width Gain EQ1 100Hz 1.4Q 0.0dB Navigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dB Presets Preset Recall Preset Store Preset Name Store My System Output DSP block diagram Input DSP block diagramDSP Processing Layout Stereo / Mono Formats Input Channels DSP Processing A Freq Shape HPF 20.0Hz LR24 High and Low shelving filters Parametric EqualisationParametric filters Output Channels DelayGain and Polarity High and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24 Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing Limiters Utility functions Utilities Audio Input Connectors Racking, Cables and Connections AMP-890 Aspect System Amplification Rack Input Connections Options Output Connections Amplifier Rack Signal Wiring Mid-High Outputs Break-out Cables NL4 bass Extension Cables Break-out cables NL8 mid-high Mains Connections General Features & Facilities T-45 High Efficiency Audio Power Amplifiers Front Panel Functions T-25 Front Panel Functions T-45 Mechanical Installation Audio Connections & Controls Voltage Range Polarity Gain and Sensitivity SettingsInput Impedance Damping Factor Attenuation & Gain Setting Cooling System Long Speaker Lines Maintenance To rotate the horn moulding from ‘A’ mode to ‘B’ mode Removal of the high frequency driver To rotate the horn moulding from ‘B’ mode to ‘A’ mode Removal of the high-mid frequency driver Removal of the low-mid frequency drive units General Maintenance Paintwork TA-890 Technical Specifications Serial Numbers Warranty TA-890