MAC2 LAN Bridge, MAC Address, Azalia Codec | Tyan Computer S2912

MAC2 LAN Bridge

Enable MAC2 LAN Bridge.

Options: Enabled / Disabled

MAC Address

Read only.

Azalia Codec

Enable/disable Azalia audio interface.

Options: Enabled / Disabled

SATA0 / SATA1 / SATA2 Controller

Enable/disable First Serial ATA Device.

NOTE: Mobile platform, enable SATA, SAVE and EXIT BIOS SETUP. Then must do a power cycle during next POST.

Options: Enabled / Disabled

Interrupt Mode

Select interrupt mode between 8259/PIC mode or APIC mode.

Options: APIC / PIC

45

http://www.tyan.com

Image 45

Tyan Computer S2912 warranty MAC2 LAN Bridge, MAC Address, Azalia Codec, SATA0 / SATA1 / SATA2 Controller, Interrupt Mode

Contents

S2912 Thunder n3600R Board Installation Table of Contents IntroductionBios Diagnostics Check the box contents Page Hardware Specifications IntroductionCongratulations Expansion Slots System ManagementForm Factor Regulatory Board Installation Board Image Thunder n3600R S2912WG2NR Block Diagram Block Diagram Thunder n3600R S2912G2NR Block Diagram Jumper Legend Board Parts, Jumpers and Connectors FRNTUSB23 J3 FRNTUSB45 J4 Jumper/Connector FunctionPage SYSFAN7 4-pin CPU Fan Connector SYSFAN5/6 3-pin Fan Connector FRNTUSB45 Ipmb J14 Ipmb Connector J2/J3/J4 USB Front Panel Header J2/J4J26 Tyfp Front Panel Header COM2 COM2 J95 COM2 Header J113 LCD Model Pin HeaderJ15 Tyan Front Panel 2 for Barebone reserved JP2 JP3 JP1 JP1 SAS Disable Jumper for S2912WG2NR only J111 Fan Connector for Barebone reservedJP3 Clear Cmos Jumper Normal Default JP2 Opma Card Supporting Select Jumper Tips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching IDE Drive Cable Attaching Drive CablesPage Installing Add-In Cards LAN LED Color Definition Connecting External Devices Applying power to the board Installing the Power Supply Finishing Up Bios About the BiosStarting Setup Case of Problems Setup VariationsGetting Help Main Bios Setup Main Extended Memory Cache RamSystem Time / System Date Reset Configuration Data Installed O/SAdvanced LPC Port HT-LDT Frequency Hammer ConfigurationNode Interleave Dram Bank Interleave ECC Options Sub-Menu ECC Mode Multiprocessor SpecificationECC Error Checking Auto DQS Training L2 ECC Scrub Control ECC Error LogDram ECC Scrub Control ECC Scrub Redirection Iommu Size Iommu Integrated Devices USB Bios Legacy SupportUSB Control Self-Healing MAC2 LAN Bridge Interrupt ModeMAC Address Azalia Codec NV RAID Configuration Sub-Menu FirstWare Language FirstWare Configuration Integrated SAS Controller Sub-Menu PCI Configuration Available Oprom SpacePage IDE Configuration Large Disk Access ModeLocal Bus IDE Adapter Primary Master/Slave Sub-Menu LBA Mode ControlType Multi-Sector Transfers Transfer Mode Ultra DMA ModeBit I/O Legacy Diskette a Selects floppy type Floppy Configuration Serial Port a 7 I/O Device ConfigurationBase I/O Address Interrupt Mode Parallel PortDMA Channel Floppy Disk Controller COM Port Address Console RedirectionBaud Rate Console Type Event Log Capacity DMI Event LoggingEvent Log Validity View DMI Event Log Hardware Monitoring AutoFan Mode Security Boot Boot Priority OrderExcluded from boot order Enable Acpi PowerPower Button Off Tgio Spread Spectrum High Precision Event timer After Power FailureAMD PowerNow Sata Spread Spectrum Exit Page Diagnostics Flash UtilityMemory, Video, CPU Code Beeps / Description Phoenix Bios Post Code Display shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Technical Support Returning Merchandise for Service