Console Redirection, COM Port Address | Tyan Computer S2912 instruction

3.4.8 Console Redirection

This setting allows you to configure Console Redirection.

COM Port Address

If enabled, it will use a port on the motherboard.

Options: Enabled / Disabled

Baud Rate

Enables the specified baud rate.

Options: 300 / 1200 / 2400 / 9600 / 19.2K / 38.4K / 57.6K / 115.2K

Console Type

Enables the specified console type.

Options: VT100 / VT100, 8bit / PC-ANSI / VT100+ / VT-UTF8 / ASCII

Flow Control

Enables flow control.

Options: Disabled / XON/XOFF / CTS/RTS

Console Connection

It indicates whether the console is connected directly to the system or a modem is used to connect.

Options: Direct / via Modem

Continue C.R. After POST

Enables Console Redirection after OS has loaded.

Options: Off / On

56

http://www.tyan.com

Image 56

Tyan Computer S2912 Console Redirection, COM Port Address, Baud Rate, Console Type, Flow Control, Console Connection

Contents

Thunder n3600R S2912 Table of Contents Introduction Board InstallationBios Diagnostics Check the box contents Page Congratulations Hardware SpecificationsIntroduction System Management Expansion SlotsForm Factor Regulatory Board Installation Board Image Block Diagram Thunder n3600R S2912WG2NR Block Diagram Thunder n3600R S2912G2NR Block Diagram Board Parts, Jumpers and Connectors Jumper Legend Jumper/Connector Function FRNTUSB23 J3 FRNTUSB45 J4Page SYSFAN5/6 3-pin Fan Connector SYSFAN7 4-pin CPU Fan Connector FRNTUSB45 J26 Tyfp Front Panel Header Ipmb J14 Ipmb ConnectorJ2/J3/J4 USB Front Panel Header J2/J4 COM2 J15 Tyan Front Panel 2 for Barebone reserved COM2 J95 COM2 HeaderJ113 LCD Model Pin Header JP2 JP3 JP1 J111 Fan Connector for Barebone reserved JP1 SAS Disable Jumper for S2912WG2NR onlyJP3 Clear Cmos Jumper Normal Default JP2 Opma Card Supporting Select Jumper Tips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching Drive Cables Attaching IDE Drive CablePage Installing Add-In Cards Connecting External Devices LAN LED Color Definition Installing the Power Supply Applying power to the board Finishing Up Starting Setup BiosAbout the Bios Getting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Extended MemoryCache Ram Installed O/S Reset Configuration DataAdvanced LPC Port Hammer Configuration HT-LDT FrequencyNode Interleave Dram Bank Interleave Multiprocessor Specification ECC Options Sub-Menu ECC ModeECC Error Checking Auto DQS Training ECC Error Log L2 ECC Scrub ControlDram ECC Scrub Control ECC Scrub Redirection Iommu Iommu Size USB Bios Legacy Support Integrated DevicesUSB Control Self-Healing Interrupt Mode MAC2 LAN BridgeMAC Address Azalia Codec NV RAID Configuration Sub-Menu FirstWare Configuration FirstWare Language PCI Configuration Available Oprom Space Integrated SAS Controller Sub-MenuPage Local Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode LBA Mode Control Primary Master/Slave Sub-MenuType Multi-Sector Transfers Bit I/O Transfer ModeUltra DMA Mode Floppy Configuration Legacy Diskette a Selects floppy type 7 I/O Device Configuration Serial Port aBase I/O Address Interrupt Parallel Port ModeDMA Channel Floppy Disk Controller Console Redirection COM Port AddressBaud Rate Console Type DMI Event Logging Event Log CapacityEvent Log Validity View DMI Event Log AutoFan Mode Hardware Monitoring Security Excluded from boot order BootBoot Priority Order Power Enable AcpiPower Button Off Tgio Spread Spectrum After Power Failure High Precision Event timerAMD PowerNow Sata Spread Spectrum Exit Page Memory, Video, CPU DiagnosticsFlash Utility Phoenix Bios Post Code Code Beeps / Description Display shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Returning Merchandise for Service Technical Support