Enable Acpi, Power Button Off | Tyan Computer S2912 instruction

3.7 Power

These settings allow you to control the Power Configuration.

Enable ACPI

This allows you to enable or disable ACPI BIOS (Advance Configuration and Power Interface).

Options: No / Yes

ACPI S3

It allows you to disable the save-to-ram power mode.

Options: Enabled / Disabled

Power Button Off

[Enabled] will let power button possible to shutdown the system in legacy OS without holding for 4 seconds.

[Disabled] will force 4-second power button to shutdown the system. Options: Enabled / Disabled

TGIO Spread Spectrum

Disable or Enable TGIO Spread Spectrum

Options: Disabled / Down Spread

LDT Spread Spectrum

Disable or Enable LDT Spread Spectrum

Options: Disabled / Center Spread

61

http://www.tyan.com

Image 61

Tyan Computer S2912 warranty Enable Acpi, Power Button Off, Tgio Spread Spectrum, LDT Spread Spectrum

Contents

S2912 Thunder n3600R Board Installation Table of Contents IntroductionBios Diagnostics Check the box contents Page Introduction Hardware SpecificationsCongratulations Expansion Slots System ManagementForm Factor Regulatory Board Installation Board Image Thunder n3600R S2912WG2NR Block Diagram Block Diagram Thunder n3600R S2912G2NR Block Diagram Jumper Legend Board Parts, Jumpers and Connectors FRNTUSB23 J3 FRNTUSB45 J4 Jumper/Connector FunctionPage SYSFAN7 4-pin CPU Fan Connector SYSFAN5/6 3-pin Fan Connector FRNTUSB45 J2/J3/J4 USB Front Panel Header J2/J4 Ipmb J14 Ipmb ConnectorJ26 Tyfp Front Panel Header COM2 J113 LCD Model Pin Header COM2 J95 COM2 HeaderJ15 Tyan Front Panel 2 for Barebone reserved JP2 JP3 JP1 JP1 SAS Disable Jumper for S2912WG2NR only J111 Fan Connector for Barebone reservedJP3 Clear Cmos Jumper Normal Default JP2 Opma Card Supporting Select Jumper Tips on Installing Motherboard in Chassis Installing the Processors Back plate Assembly Page Installing the Memory Memory Installation Procedure Refer to the following table for supported DDR2 populations Attaching IDE Drive Cable Attaching Drive CablesPage Installing Add-In Cards LAN LED Color Definition Connecting External Devices Applying power to the board Installing the Power Supply Finishing Up About the Bios BiosStarting Setup Setup Variations Case of ProblemsGetting Help Main Bios Setup Main Cache Ram Extended MemorySystem Time / System Date Reset Configuration Data Installed O/SAdvanced LPC Port HT-LDT Frequency Hammer ConfigurationNode Interleave Dram Bank Interleave ECC Options Sub-Menu ECC Mode Multiprocessor SpecificationECC Error Checking Auto DQS Training L2 ECC Scrub Control ECC Error LogDram ECC Scrub Control ECC Scrub Redirection Iommu Size Iommu Integrated Devices USB Bios Legacy SupportUSB Control Self-Healing MAC2 LAN Bridge Interrupt ModeMAC Address Azalia Codec NV RAID Configuration Sub-Menu FirstWare Language FirstWare Configuration Integrated SAS Controller Sub-Menu PCI Configuration Available Oprom SpacePage Large Disk Access Mode IDE ConfigurationLocal Bus IDE Adapter Primary Master/Slave Sub-Menu LBA Mode ControlType Multi-Sector Transfers Ultra DMA Mode Transfer ModeBit I/O Legacy Diskette a Selects floppy type Floppy Configuration Serial Port a 7 I/O Device ConfigurationBase I/O Address Interrupt Mode Parallel PortDMA Channel Floppy Disk Controller COM Port Address Console RedirectionBaud Rate Console Type Event Log Capacity DMI Event LoggingEvent Log Validity View DMI Event Log Hardware Monitoring AutoFan Mode Security Boot Priority Order BootExcluded from boot order Enable Acpi PowerPower Button Off Tgio Spread Spectrum High Precision Event timer After Power FailureAMD PowerNow Sata Spread Spectrum Exit Page Flash Utility DiagnosticsMemory, Video, CPU Code Beeps / Description Phoenix Bios Post Code Display shadow-area Code Beeps / Description Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Page Technical Support Returning Merchandise for Service