Floppy Configuration, Floppy check | Tyan Computer S2937, N3600T

3.4.4Floppy Configuration

This section allows you to select the Floppy Configuration.

Legacy Diskette A Selects floppy type.

Options: Disabled / 360 KB, 5.25 in / 1.2 MB, 5.25 in / 720 KB, 3.5 in / 1.44/1.25 MB, 3.5 in / 2.88 MB, 3.5 in

Floppy check

Options: Disabled / [Enabled]

56

http://www.tyan.com

Image 56

Tyan Computer S2937, N3600T warranty Floppy Configuration, Legacy Diskette a Selects floppy type, Floppy check

Contents

Thunder n3600T Table of Contents Appendix Glossary …………………………Page Technical Support Check the box contents Hardware Specifications Congratulations Power Integrated 2D/3D PCI GraphicsIntegrated I/O Interfaces Back Panel I/O Ports Software Specifications OS Operating Systems Support Board Installation How to install our products right… the first time Board Image Block Diagram Board Parts, Jumpers and Connectors Jumper settings JP2 JP3 JP1 SAS Disable Jumper JP1 Normal Default ClearOpma card supporting select header JP2 Clear Cmos JP3 Front Panel Header J26 JP10 JP9 JP11 Ipmb Connector Ipmb LAN1/LAN2 Enable/ Disable Jumper JP9, JP10TPM Enable/ Disable Jumper JP11 Signal Pin Onboard VGA Enable/ Disable Jumper JP8 CPU1 & CPU2 FAN Header CPU FAN1, CPU FAN2 System FAN Headers SYS FAN1/2/3/4/5/6/7 J116 J118 J113 J111 J15 Tyan Front Panel 2 for Barebones J15LCD Module Header for Barebones J113 Fan Connector for Barebones J111 Tips on Installing Motherboard in Chassis Page Installing the Processors Back plate Assembly Page Processor Installation Page Installing the Memory Memory Installation Procedure Thermal Interface Material Heatsink Installation Procedures Type a CAM Lever Type Installation Finishing Installing the Heatsink Type B Screw Retention Type Heatsink Attaching Drive Cables Sata Drivers Drive does not power on Floppy Drives Installing Add-In Cards PCI-E x 16 slot w/ x 4 signal PCI-E x 16 slot w/ x 8 signal Connecting External Devices Description Left LED Right LED 24-pin Pin Installing the Power SupplyApplying power to the board Finishing Up Bios About the Bios Starting Setup Getting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Advanced Installed O/SReset Configuration Data Hammer Configuration HT-LDT FrequencyNode Interleave Dram Bank Interleave Multiprocessor Specification ECC Options Sub-Menu ECC ModeAuto DQS Training Processor Assisted Virtualizations ECC Error Checking ECC Error LogECC Multibit Error Detection ChipKill Memory Controller Options Sub-Menu Mem Hole Remap Iommu Size Memory Config Options Sub-Menu Mem Clock Mode Memory Clock USB Bios Legacy Support Interrupt ModeIntegrated Devices USB Control NV RAID Configuration Sub-Menu Sata port 0/1/2/3/4/5 Raid Local Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode LBA Mode Control Primary Master / Slave Sub-MenuType Multi-Sector Transfers Bit I/O Transfer ModeUltra DMA Mode Floppy check Floppy ConfigurationLegacy Diskette a Selects floppy type 5 I/O Device Configuration Serial Port aBase I/O Address Interrupt Mode Parallel PortDMA Channel Floppy Disk Controller AutoFan Mode Hardware Monitor / Ipmi Console Redirection COM Port AddressBaud Rate Console Type DMI Event Logging Event Log CapacityEvent Log Validity View DMI Event Log Security Boot EndLess PXE Loop Boot Device Priority Boot Priority OrderExcluded from boot order Power Enable AcpiPower Button Off After Power Failure Spread Spectrum Tgio Spread Spectrum LDT Spread SpectrumSata Spread Spectrum CPU PLL Spread Spectrum Acpi Table High Precision Event timer AMD PowerNowAcpimcfg Table Acpi Srat Table Exit Page Memory, Video, CPU DiagnosticsFlash Utility Phoenix Bios Post Code Code Beeps / Description PEM Page Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Technical Support