Onboard VGA Enable/ Disable Jumper JP8 | Tyan Computer N3600T

2.13 – Onboard VGA Enable/ Disable Jumper (JP8)

Default, Enable

Install Jumper to disable onboard VGA

(Default)

SYS FAN7	SYS FAN3
SYS FAN7
	SYS FAN1
SYS FAN5	SYS FAN4
	CPU2 FAN

SYS FAN2

SYS FAN6

CPU1 FAN

17

http://www.TYAN.com

Image 17

Tyan Computer N3600T, S2937 warranty Onboard VGA Enable/ Disable Jumper JP8

Contents

Thunder n3600T Table of Contents Appendix Glossary …………………………Page Technical Support Check the box contents Congratulations Hardware Specifications Integrated 2D/3D PCI Graphics PowerIntegrated I/O Interfaces Back Panel I/O Ports OS Operating Systems Support Software Specifications How to install our products right… the first time Board Installation Board Image Block Diagram Board Parts, Jumpers and Connectors Jumper settings JP2 JP3 JP1 Normal Default Clear SAS Disable Jumper JP1Opma card supporting select header JP2 Clear Cmos JP3 JP10 JP9 JP11 Front Panel Header J26 LAN1/LAN2 Enable/ Disable Jumper JP9, JP10 Ipmb Connector IpmbTPM Enable/ Disable Jumper JP11 Signal Pin Onboard VGA Enable/ Disable Jumper JP8 System FAN Headers SYS FAN1/2/3/4/5/6/7 CPU1 & CPU2 FAN Header CPU FAN1, CPU FAN2 J116 J118 J113 J111 J15 Tyan Front Panel 2 for Barebones J15LCD Module Header for Barebones J113 Fan Connector for Barebones J111 Tips on Installing Motherboard in Chassis Page Installing the Processors Back plate Assembly Page Processor Installation Page Installing the Memory Memory Installation Procedure Thermal Interface Material Type a CAM Lever Type Installation Heatsink Installation Procedures Type B Screw Retention Type Heatsink Finishing Installing the Heatsink Attaching Drive Cables Sata Drivers Floppy Drives Drive does not power on PCI-E x 16 slot w/ x 4 signal PCI-E x 16 slot w/ x 8 signal Installing Add-In Cards Description Left LED Right LED Connecting External Devices 24-pin Pin Installing the Power SupplyApplying power to the board Finishing Up Starting Setup Bios About the Bios Getting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Advanced Installed O/SReset Configuration Data HT-LDT Frequency Hammer ConfigurationNode Interleave Dram Bank Interleave ECC Options Sub-Menu ECC Mode Multiprocessor SpecificationAuto DQS Training Processor Assisted Virtualizations ECC Error Log ECC Error CheckingECC Multibit Error Detection ChipKill Iommu Size Memory Controller Options Sub-Menu Mem Hole Remap Memory Clock Memory Config Options Sub-Menu Mem Clock Mode Interrupt Mode USB Bios Legacy SupportIntegrated Devices USB Control Sata port 0/1/2/3/4/5 Raid NV RAID Configuration Sub-Menu Local Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode Primary Master / Slave Sub-Menu LBA Mode ControlType Multi-Sector Transfers Bit I/O Transfer ModeUltra DMA Mode Floppy check Floppy ConfigurationLegacy Diskette a Selects floppy type Serial Port a 5 I/O Device ConfigurationBase I/O Address Interrupt Parallel Port ModeDMA Channel Floppy Disk Controller Hardware Monitor / Ipmi AutoFan Mode COM Port Address Console RedirectionBaud Rate Console Type Event Log Capacity DMI Event LoggingEvent Log Validity View DMI Event Log Security Boot EndLess PXE Loop Boot Device Priority Boot Priority OrderExcluded from boot order Enable Acpi PowerPower Button Off After Power Failure LDT Spread Spectrum Spread Spectrum Tgio Spread SpectrumSata Spread Spectrum CPU PLL Spread Spectrum AMD PowerNow Acpi Table High Precision Event timerAcpimcfg Table Acpi Srat Table Exit Page Memory, Video, CPU DiagnosticsFlash Utility Code Beeps / Description Phoenix Bios Post Code PEM Page Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Technical Support