BULLETIN RC454

A GUIDE TO BURNING COAL IN YOUR FURNACE

When the fire is well established and the room is be- coming warm, partially close the dampers. Some experimenting will have to take place with each particular setting of all dampers and controls as the chimney provides the draft necessary to not only exhaust the smoke, but to pull combustion air into the heater as well - and no two chimney’s perform the same. Under ideal draft conditions, one should be able to turn the secondary air supply below the feed door (some models) to a near closed position - but leave the ash pit damper at least partially open to prevent the fire from going out. Adjust the stove pipe damper to reduce the draft on the fire. With anthracite there will be short blue flames above the coal, except when the fire is started or a new charge is added. If, however, there is no flame then the fire needs more air from the bottom (unless it is near the end of its burn cycle and needs to be re- charged).

Only when the coal is burned down to half its origi- nal depth it is time to add fresh coal. When doing so, open the stove pipe damper and turn the thermo- stat damper to high, which will allow the fire to burn off any accumulated gases. Open the feed door, and with a small rake, hoe, or hooked poker pull the glowing coals to the front of the firebox. Try not to disturb the fire too much. Next, add a fresh charge to the back being careful not to seal off the top. Close the feed door, but leave the spin damper (or thermostat) open for a few minutes until the volatile gases have burned off. It is not necessary to shake down the ashes each time you refuel the furnace. Experience will be your best teacher.

BANKING THE FIRE:

For extended operation, such as overnight, the fire will need to be banked. To do so heap coal up along the sides and back of the firebox so that the fire gradually burns it over a longer period of time. The intensity of the fire will also be reduced without letting it go out. Follow the same procedure as for refueling. If possible, avoid shaking, as a heavier layer of ash will help reduce the intensity of the fire during this time. After loading, let the fire establish itself for about 30 minutes. Then close your damper and automatic control to the point where the house does not become too cold. It is important that you begin banking early enough before retiring or leav- ing that you can make necessary adjustments after the fire is well established.

To revive a coal fire that is almost out, (1) open the ash door and stove pipe damper and close the spin damper under the door to get a good draft through the grate. (2) place a thin layer of dry coal over the entire top of the fire. DO NOT POKE OR SHAKE THE FIRE AT THIS TIME! (3) after the fresh coal has become well ignited shake the grate (just a little), refuel.

DO NOT burn coke, charcoal, high volatile bitumi- nous coal, sub bituminous, lignite or cannel coal (sometimes called channel coal or candle coal).

NEVER burn wax or chemically impregnated saw- dust logs - their intended use is for fireplaces only.

NEVER fill the stove or furnace above the firebrick or cast iron liner.

USSC

17

Page 17
Image 17
United States Stove 1602G, 1802G installation instructions Banking the Fire

1602G, 1802G specifications

The United States Stove Company proudly presents the 1802G and 1602G models, two exceptional additions to their line of pellet stoves, designed to meet the heating needs of modern homes while providing an array of features that enhance comfort and convenience.

The United States Stove 1802G is a powerful pellet stove with a heating capacity of up to 1,800 square feet, making it suitable for larger spaces. With a sleek design and a decorative cast iron door, this unit not only provides warmth but also adds an aesthetic appeal to your living environment. The 1802G is equipped with a large hopper capacity, allowing for extended burn times and minimizing the need for frequent refueling. One key feature is its state-of-the-art auto igniter, which ensures a reliable and hassle-free start-up.

The 1602G model, on the other hand, is designed for smaller spaces, heating up to 1,200 square feet efficiently. This model shares many features with the 1802G but is compact enough to fit snugly into tight spaces without sacrificing performance. The double-walled construction of both units promotes safety and efficiency, contributing to low emissions and optimal heat preservation.

Both models come equipped with advanced technology, including a programmable thermostat that allows users to set the stove to operate according to their preferred schedules, optimizing energy usage while maintaining comfort. The EPA-certified design ensures that both stoves meet stringent environmental standards, making them an eco-friendly choice for homeowners.

Additionally, these stoves feature a built-in fan that circulates warm air throughout the space, enhancing the overall heating efficiency. The user-friendly control panel gives consumers easy access to adjust settings, monitor fuel levels, and manage the burn rate, providing both versatility and control.

Durability is a hallmark of the United States Stove Company, and the 1802G and 1602G models are no exception. Constructed from high-quality materials, these pellet stoves are built to withstand the rigors of daily use while ensuring longevity.

In conclusion, the United States Stove 1802G and 1602G models represent the perfect blend of functionality, efficiency, and style. With advanced features, eco-friendly technology, and robust construction, they are ideal choices for homeowners seeking reliable and effective heating solutions. Whether you require a powerful unit for a spacious area or a compact model for a cozy room, these stoves deliver exceptional performance and comfort.