United States Stove 1802G Introduction, Disclaimer Notice, Clearances, Locating Your Furnace

INTRODUCTION

Thank You for your purchase of a U.S. Stove Wood/Coal Burning Gravity Style (Up-Flow) Furnace. Your decision to buy our Clayton Furnace was undoubtedly reached af- ter much careful thought and consideration. We are very proud you chose this furnace and trust you will receive the comfort and economy that others realize when heat- ing with a U.S. Stove product.

Your dealer is important in your experience with the fur- nace not only with the purchase, but for recommen- dations for professional installation in your home. The qualified professional installer has been expertly trained in solid-fuel furnace installation to assure the safety and comfort for your family while saving you money. Trust your experienced installer. He is a specialist in this field.

IMPORTANT

Before installing and using your Clayton furnace, please read the following pages thoroughly and carefully. If you follow the instructions, your Clayton furnace will give you safe and more dependable service for years to come.

•First step: Check your local codes. This installation must comply with their rulings.

•Do Not install this furnace in a mobile home or trailer

•Always have a smoke or ionization detector and a CO detector installed in your home.

•To prevent injury or damage, do not allow anyone who is unfamiliar with the furnace to operate it.

•This furnace must be installed ONLY in the prescribed manner shown in illustrations 1, 2, or 3 under the In- stallation Examples in this manual. It is NEVER to be installed as a counter-flow or down-draft furnace, or in any manner wherein the heated air is directed in a downward flow into the home or toward to an existing central furnace.

•NEVER INSTALL outside the home.

•Spend adequate time with your furnace to become well acquainted with the different settings and how each will affect its burning patterns. It is impossible to state just how each setting will affect your furnace be- cause of the variations in each installation.

DISCLAIMER NOTICE

The BTU ranges and heating capacity specifications are provided as a guide and in no way guarantee the output or capacity of this unit. The actual BTU output depends on the type of fuel being burned and its conditions, the thermostat setting, the draft adjustment and the chimney to which the unit is attached. The actual area that this unit will heat depends on factors such as the conditions of the building, heat loss, type of construction, amount of insulation, type of air movement, the location of the unit and more importantly the duct work and return air facility.

Do not place the furnace directly on a combustible floor. If you are placing it on a combustible floor, an approved fire retardant material, equivalent to 3/8” UL Listed mill- board, should be placed under the unit. The material must extend at least 16 inches beyond the front of the unit and 8 inches on either side of the fuel loading door opening. It must also extend underneath the chimney connector and to each side of the connector by at least 2 inches.

CLEARANCES

COMBUSTIBLE WALL

		Model	Model
		1602 - 20”	1602 - 15”
		1802 - 25”	1802 - 28”
WALL			(TOP VIEW)
COMBUSTIBLE	Model		MINIMUM CLEARANCES
	1602 - 22”
			TO A COMBUSTIBLE
	1802 - 19”	FLUE
			WALL
			CAUTION:
			DO NOT store
	Model		combustible or
			flammable materials or
	1602 - 12”
			liquids near the
	1802 - 8”
			furnace.

REDUCED CLEARANCES

NFPA guidelines and most codes permit reduced clear- ances to combustible walls and ceilings if adequate protection is added. A common mistake is to assume that sheet metal, masonry, or millboard placed directly against a wall protects it. Materials installed in this man- ner actually provides very little protection. These materials are good heat conductors, so they will be almost as hot on their back side as they are on the exposed side. There- fore, the combustible wall behind is still a fire hazard.

A wall can be kept cool using these items but only if they are mounted and spaced out from the wall by an inch or two to allow free air circulation behind the protective panel. The protective panel should also have a gap be- tween the floor and ceiling.

Three rules to follow when constructing wall protectors:

1.Non-combustibility of all materials including mount- ing and supporting.

2.A well ventilated air space between protector and wall.

3.Sufficient strength and rigidity so that the protector and air space will be durable.

2” FROM CEILING

Warning:

Do not alter this appliance in any way other than speci- fied in these instructions. Doing so may void your warranty.

LOCATING YOUR FURNACE

The furnace is to be installed maintaining the clearances specified in the following illustrations.

CONSTRUCTING

NON-COMBUSTIBLE

WALLS

1” AIR SPACE

2” FROM FLOOR

PROTECTIVE COVERING AND ALL SUPPORTS MUST BE NON-COMBUSTIBLE

2 USSC