Vermont Casting 1945 What Kind of Chimney to Use, Masonry Chimneys, Prefabricated Chimneys

Defiant Woodburning Stove

What Kind of Chimney to Use

You must connect the Defiant to a code-approved masonry chimney with a flue liner, to a relined masonry chimney that meets local codes, or to a prefabricated metal chimney that complies with the requirements for Type HT chimneys in the Standard for Chimneys, Factory-Built, Residential Type and Building Heating Appliance, UL 103. Figure 3 illustrates the two types. The chimney and chimney connector must be in good condition and kept clean.

If you use an existing masonry chimney, it must be inspected to ensure it is in a safe condition before the stove is installed. Your local professional chimney sweep, building inspector, or fire department official will be able to inspect the chimney or provide a refer- ral to someone who can. See “Chimney and Fireplace hazards”, in the appendix, for particulars.

A prefabricated double- wall insulated chimney

A tile-lined masonry chimney

ST241

Fig. 3 Approved chimney types.

The chimney must extend at least 3’ (194 mm) above the highest pint where it passes through or past a roof, and at least 3’ (610 mm) higher than any part of a build- ing within 10’ (3 m) horizontally. (Fig. 4)

For proper draft and good performance, any chimney used with a Defiant should extend at least 16’ (5 m) above the flue collar of the stove.

	0 To 10'
	2' Min. 3'	0 To 10'
	Min.
		2' Min. 3'
		Min.
	Reference
	Point	AC617
Fig. 4	The 2’-3’10’ Chimney Rule.
6

Masonry Chimneys

An inspection of the chimney must confirm that it has a lining. Do not use an unlined chimney. The chimney should have no cracks, loose mortar, other signs of deterioration, and blockage. Repair any defects before the chimney is used with your stove.

Unused openings in an existing masonry chimney must be sealed with masonry to the thickness of the chimney wall, and the chimney liner should be repaired. Open- ings sealed with pie plates or wallpaper are a hazard and should be sealed with mortar or refractory cement. In the event of a chimney fire, flames and smoke may be forced out of these unused thimbles.

The chimney should be thoroughly cleaned before use.

A newly-built masonry chimney must conform to the standards of your local building code or, in the absence of a local code, to a recognized national code. Masonry chimneys must be lined, either with code-approved masonry or pre-cast refractory tiles, stainless steel pipe, or a code-approved, “poured-in-place” liner. The chimney’s clean-out door must seal tightly. A loose or leaky clean-out door can weaken chimney draft to the stove, causing performance problems.

Prefabricated Chimneys

A prefabricated metal chimney must be one tested and listed for use with solid-fuel burning appliances to the High-Temperature (H.T.) Chimney Standard UL-103- 1985 (2100°F) for the United States, and High Temper- ature (650°C) Standard ULC S-629 for Canada.

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

Chimney Size

An Defiant with an 8” (203 mm) flue collar is approved for venting into a masonry chimney with a nominal flue size of 8” x 8” (203 x 203 mm) or 8” x 12” (203 x 305 mm), and into a round flue with nominal flue size of 8” (203 mm). An Defiant with a 6” (152 mm) flue collar is approved for venting into a masonry chimney with a nominal flue size of 8” x 8” (203 x 203 mm), and into a round flue with nominal flue of 6” (152 mm).

NOTE: When installed with a 6” flue collar, the Defi- ant may not be operated with the front doors open.

Whatever the flue collar size, an Defiant may be vented into larger chimneys as well. However, chimneys with liners larger than 8” x 12” (203 x 305 mm) may experience rapid cooling of smoke and reduction in draft, especially if the chimneys are located outside the home. These large chimneys may need to be insulated or have their flues relined for proper stove performance.

30001693