Vermont Casting SDDVTCMB, SDDVTCVG Venting Requirements and Options Direct Vent ONLY, 20012734

Models: SDDVTCB, SDDVTEB, SDDVTMB, SDDVTBS, SDDVTCH, SDDVTVG, SDDVTBD,SDDVTCCB, SDDVTCEB, SDDVTCMB, SDDVTCBS, SDDVTCCH, SDDVTCVG, SDDVTCBD SDDVTCMB SDDVTCVG

1 52
Download 52 pages 56.79 Kb
Page 13
Image 13
Venting Requirements and Options -

Venting Requirements and Options -

Direct Vent ONLY

Approved Vent System Components

The Stardance Heater must be vented to the outdoors through an adjacent exterior wall or through the roof. The venting system must be comprised of the appropri- ate listed venting components specified on this page. These parts are available from DuraVent Corporation, Selkirk Corporation or your Vermont Castings Dealer.

See Figure 4 for dimensions relevant to the standard minimum-vent kits.

Simpson DuraVent Components

www.duravent.com

Phone: 1-800-835-4429, Fax: 1-707-446-4740

Minimum Horizontal Vent Kit

 

2792

Starter Pipe Assembly (incl. inner & outer sections)

2768*

90° Elbow, Blk.

46DVA-E90B*

45° Elbow, Gal.

46DVA-E45

6” Straight, Blk.

46DVA-06B*

9” Straight, Blk.

46DVA-09B

11” - 14⁵⁄” Adjustable Straight Section

46DVA-08AB

12” Straight

46DVA-12

24” Straight

46DVA-24B*

36” Straight

46DVA-36B

48” Straight

46DVA-48

Horizontal Vent Cap

46DVA-HC*

Wall Plate

46DVA-DC

Vinyl Siding Shield

46DVA-VSS

Snorkel Termination - 14”

46DVA-SNK14

Snorkel Termination - 36”

46DVA-SNK30

Wall Strap

46DVA-WS

Cathedral Ceiling Support Box

46DVA-CS

Storm Collar

46DVA-SC

Firestop Spacer

46DVA-FS

Flashing 0/12 - 6/12

46DVA-F6

Flashing 6/12 - 12/12

46DVA-F12

Steel Chimney Conversion Kit

 

 

Kit A (6⁵⁄” - 8⁵⁄”)

46DVA-KCA

Kit B (6⁵⁄” - 10¹⁄”)

46DVA-KCB

Kit C (6⁵⁄” - 13”)

46DVA-KCC

Masonry Chimney Conversion Kit

46DVA-KMC

Vertical Termination Cap (High Wind)

46DVA-VCH

Vertical Termination Cap (Low Profile)

46DVA-VC

*Included in Minimum Horizontal Vent Kit #2792

All DuraVent Straight vent pipe sections have a net length 1¹⁄” (37mm) less than the nominal dimension; i.e., a 6” (152mm) Straight pipe section has an effective length of 4¹⁄” (115mm).

Stardance Direct Vent/Natural Vent Gas Heater

Selkirk Corporation Vent Components

www.selkirkcorp.com

1301 W. President George Bush Highway Ste. 330 Richardson, TX 75080

Phone: 1-800-992-8368, Fax: 1-877-393-4145

Appliance Adapter

4DT-AAV

90° Elbow, Blk.

4DT-EL90B

45° Elbow, Blk.

4DT-EL45B

6” Straight, Blk.

4DT-06B

9” Straight, Blk.

4DT-09B

4” - 10” Adjustable Straight Section Blk.

4DT-AJ12B

12” Straight, Blk.

4DT-12B

18” Straight, Blk.

4DT-18B

24” Straight, Blk.

4DT-24B

36” Straight, Blk.

4DT-36B

48” Straight, Blk.

4DT-48B

Horizontal Termination

4DT-HC

Wall Thimble

4DT-WT

Vinyl Siding Standoff

4DT-VS

Snorkel Termination - 14”

4DT-ST14

Snorkel Termination - 36”

4DT-ST36

Wall Support Band

4DT-WS/B

Cathedral Ceiling Support Box

4DT-CCS

Storm Collar

4DT-SC

Firestop Spacer

4DT-FS

Flashing 0/12 - 6/12

4DT-AF6

Flashing 6/12 - 12/12

4DT-AF12

Steel Chimney

 

Horizontal Kit A

4DT-HKA

Horizontal Kit B

4DT-HKB

Vertical Kit

4DT-VKC

Masonry Chimney Kit

4DT-MCK

Vertical Termination Cap

4DT-VC

NOTE: Direct vent pipe may be used on the Natural Vent system from the top of the draft hood adapter to the ceiling.

20012734

13

Page 13
Image 13
Vermont Casting SDDVTCMB Venting Requirements and Options Direct Vent ONLY, Stardance Direct Vent/Natural Vent Gas Heater